/************************************************************************
- * OCOTEA.h - configuration for IBM 440GX Ref (Ocotea)
+ * OCOTEA.h - configuration for AMCC 440GX Ref (Ocotea)
***********************************************************************/
#ifndef __CONFIG_H
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"netdev=eth0\0" \
"hostname=ocotea\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/ocotea/uImage\0" \
#define CONFIG_PHY1_ADDR 2
#define CONFIG_PHY2_ADDR 0x10
#define CONFIG_PHY3_ADDR 0x18
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_RESET_DELAY 1000
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 100 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */
+#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */