#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
-#define CFG_DEVICE_NULLDEV 1 /* enable null device */
#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
/*
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
/*
* FLASH organization
*/
-#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_MAX_FLASH_BANKS 1
-#if (PHYS_SDRAM_1_SIZE == SZ_32M)
-/*#if 1*/
-#define CFG_FLASH_CFI /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER /* Use the common driver */
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_MAX_FLASH_SECT 128
-#else
-#define PHYS_FLASH_1_SIZE SZ_1M
-#define CFG_MAX_FLASH_SECT 19
-#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* in ticks */
-#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ)
-#endif
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define PHYS_FLASH_1_SIZE (1 * 1024 * 1024)
+#define CONFIG_SYS_MAX_FLASH_SECT 19
+#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* in ticks */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ)
-#define CFG_MONITOR_BASE PHYS_FLASH_1
-#define CFG_MONITOR_LEN SZ_256K
+#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH
-#define ENV_IS_SOLITARY
-#define CFG_ENV_ADDR 0x4000
-#define CFG_ENV_SIZE SZ_8K
-#define CFG_ENV_SECT_SIZE SZ_8K
-#define CFG_ENV_ADDR_REDUND 0x6000
-#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR 0x4000
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_SECT_SIZE (8 * 1024)
+#define CONFIG_ENV_ADDR_REDUND 0x6000
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_OVERWRITE
/*
* Size of malloc() pool
*/
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-/* XXX #define CFG_MALLOC_LEN (SZ_64K - CFG_GBL_DATA_SIZE)*/
-#define CFG_MALLOC_LEN SZ_4M
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/*
* The stack size is set up in start.S using the settings below
*/
-/* XXX #define CONFIG_STACKSIZE SZ_8K /XXX* regular stack */
-#define CONFIG_STACKSIZE SZ_1M /* regular stack */
+#define CONFIG_STACKSIZE (1 * 1024 * 1024) /* regular stack */
/*
* Hardware drivers
/*
* NS16550 Configuration
*/
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE (-4)
-#define CFG_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */
-#define CFG_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */
+#define CONFIG_SYS_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*#define CONFIG_SKIP_RELOCATE_UBOOT*/
/*#define CONFIG_SKIP_LOWLEVEL_INIT */
/*
* NAND flash
*/
-#define CFG_MAX_NAND_DEVICE 1
-#define CFG_NAND_BASE 0x04000000 + (2 << 23)
-#define CONFIG_NEW_NAND_CODE
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x04000000 + (2 << 23)
+#define NAND_ALLOW_ERASE_ALL 1
/*
- * JFFS2 partitions (mtdparts command line support)
+ * partitions (mtdparts command line support)
*/
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=omapflash.0,nand0=omapnand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:8k@16k(env),8k(r_env),448k@576k(u-boot);omapnand.0:48M(rootfs0),48M(rootfs1),-(data)"
-
-#if 0
-#define CONFIG_COMMANDS (CFG_CMD_BDI | \
- CFG_CMD_BOOTD | \
- CFG_CMD_DHCP | \
- CFG_CMD_ENV | \
- CFG_CMD_FLASH | \
- CFG_CMD_IMI | \
- CFG_CMD_LOADB | \
- CFG_CMD_NET | \
- CFG_CMD_MEMORY | \
- CFG_CMD_PING | \
- CFG_CMD_RUN)
-
-#else
-#define CONFIG_COMMANDS (CFG_CMD_BDI | \
- CFG_CMD_BOOTD | \
- CFG_CMD_DHCP | \
- CFG_CMD_ENV | \
- CFG_CMD_FLASH | \
- CFG_CMD_NAND | \
- CFG_CMD_IMI | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_LOADB | \
- CFG_CMD_NET | \
- CFG_CMD_MEMORY | \
- CFG_CMD_PING | \
- CFG_CMD_RUN)
+#define MTDPARTS_DEFAULT "mtdparts=" \
+ "omapflash.0:8k@16k(env),8k(r_env),448k@576k(u-boot);" \
+ "omapnand.0:4M(kernel0),40M(rootfs0),4M(kernel1),40M(rootfs1),-(data)"
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#endif
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-#define CONFIG_LOOPW
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_LOOPW
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
-#define CFG_AUTOLOAD "n" /* No autoload */
-#define CONFIG_BOOTCOMMAND "run nboot"
+#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */
+#define CONFIG_BOOTCOMMAND "run fboot"
#define CONFIG_PREBOOT "run setup"
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "setup=setenv bootargs console=ttyS0,$baudrate " \
- "$mtdparts\0" \
- "ospart=0\0" \
- "setpart=" \
- "if test -n $swapos; then " \
- "if test $ospart -eq 0; then chpart nand0,1; else chpart nand0,0; fi; "\
- "setenv swapos; saveenv; " \
- "else " \
- "chpart nand0,$ospart; " \
- "fi\0" \
- "nfsargs=setenv bootargs $bootargs " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
- "nfsroot=$rootpath root=/dev/nfs\0" \
- "flashargs=run setpart;setenv bootargs $bootargs " \
- "root=/dev/mtdblock$partition ro " \
- "rootfstype=jffs2\0" \
- "initrdargs=setenv bootargs $bootargs " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
- "iboot=bootp;run initrdargs;tftp;bootm\0" \
- "fboot=run flashargs;fsload /boot/uImage;bootm\0" \
- "nboot=bootp;run nfsargs;tftp;bootm\0"
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autostart=yes\0" \
+ "ospart=0\0" \
+ "setup=setenv bootargs console=ttyS0,$baudrate " \
+ "$mtdparts\0" \
+ "setpart=" \
+ "if test -n $swapos; then " \
+ "setenv swapos; saveenv; " \
+ "else " \
+ "if test $ospart -eq 0; then setenv ospart 1;" \
+ "else setenv ospart 0; fi; " \
+ "fi\0" \
+ "nfsargs=setenv bootargs $bootargs " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
+ "nfsroot=$rootpath root=/dev/nfs\0" \
+ "flashargs=run setpart;setenv bootargs $bootargs " \
+ "root=mtd:rootfs$ospart ro " \
+ "rootfstype=jffs2\0" \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
+ "fboot=run flashargs;nboot kernel$ospart\0" \
+ "nboot=bootp;run nfsargs;tftp\0"
#if 0 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nNetStar PBX - boot in %d sec...\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "R" /* 1st "password" */
-#define CONFIG_BOOT_RETRY_TIME 30
+#define CONFIG_AUTOBOOT_PROMPT \
+ "\nNetStar PBX - boot in %d secs...\n", bootdelay
+#define CONFIG_AUTOBOOT_DELAY_STR "." /* 1st "password" */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "# " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "# " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
-#define CFG_MEMTEST_START PHYS_SDRAM_1
-#define CFG_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
+ (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CFG_TIMERBASE OMAP1510_TIMER1_BASE
-#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */
-#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
+#define CONFIG_SYS_PVT 7 /* 2^(pvt+1), divide by 256 */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
#define OMAP5910_DPLL_DIV 1
#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \