*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC512X 1 /* MPC512X family */
-#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
/* video */
-#undef CONFIG_VIDEO
-
-#ifdef CONFIG_VIDEO
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR + 0x2100)
+#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_MISC_INIT_R
#define CONFIG_SYS_IMMR 0x80000000
-#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100)
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_MAX_NAND_DEVICE 2
-#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
#define CONFIG_SYS_NAND_SELECT_DEVICE /* driver supports mutipl. chips */
/*
/* Use SRAM for initial stack */
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_SRAM_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_SRAM_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of monitor */
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */
+#define CONFIG_SYS_PSC3
#if CONFIG_PSC_CONSOLE != 3
#error CONFIG_PSC_CONSOLE must be 3
#endif
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
* Ethernet configuration
*/
#define CONFIG_MPC512x_FEC 1
-#define CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR 0x1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_FEC_AN_TIMEOUT 1
#define CONFIG_RTC_M41T62 /* use M41T62 rtc via i2 */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+/*
+ * USB Support
+ */
+#define CONFIG_CMD_USB
+
+#if defined(CONFIG_CMD_USB)
+#define CONFIG_USB_EHCI /* Enable EHCI Support */
+#define CONFIG_USB_EHCI_FSL /* On a FSL platform */
+#define CONFIG_EHCI_MMIO_BIG_ENDIAN /* With big-endian regs */
+#define CONFIG_EHCI_DESC_BIG_ENDIAN
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#endif
+
/*
* Environment
*/
"mpc5121.nand:-(data)"
-#if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
+#if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2) || defined(CONFIG_CMD_USB)
+
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
+
+#define CONFIG_CMD_FAT
+#define CONFIG_SUPPORT_VFAT
+
#endif /* defined(CONFIG_CMD_IDE) */
/*
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#define CONFIG_TIMESTAMP
#define CONFIG_HOSTNAME mpc5121ads
-#define CONFIG_BOOTFILE mpc5121ads/uImage
-#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
+#define CONFIG_BOOTFILE "mpc5121ads/uImage"
+#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx"
#define CONFIG_LOADADDR 400000 /* default location for tftp and bootm */