#define CONFIG_MPC866 1 /* This is a MPC866 CPU */
#define CONFIG_MGSUVD 1 /* ...on a mgsuvd board */
+#define CONFIG_HOSTNAME mgsuvd
-/* Do boardspecific init */
-#define CONFIG_BOARD_EARLY_INIT_R 1
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
#define CONFIG_8xx_GCLK_FREQ 66000000
-#define CFG_SMC_UCODE_PATCH 1 /* Relocate SMC1 */
-#define CFG_SMC_DPMEM_OFFSET 0x1fc0
+#define CONFIG_SYS_SMC_UCODE_PATCH 1 /* Relocate SMC1 */
+#define CONFIG_SYS_SMC_DPMEM_OFFSET 0x1fc0
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#define CONFIG_SYS_SMC_RXBUFLEN 128
+#define CONFIG_SYS_MAXIDLE 10
-#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+#define CONFIG_SYS_CPM_BOOTCOUNT_ADDR 0x1eb0 /* In case of SMC relocation, the
+ * default value is not working */
-#define CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
+#define BOOTFLASH_START F0000000
+#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
-#undef CONFIG_BOOTARGS
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
"cp.b 200000 f0000000 ${filesize};" \
"protect on f0000000 +${filesize}\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
#define CONFIG_TIMESTAMP /* but print image timestmps */
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFFF00000
+#define CONFIG_SYS_IMMR 0xFFF00000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xf0000000
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xf0000000
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_FLASH_SIZE 32
-#define CFG_FLASH_CFI
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
+#define CONFIG_ENV_SIZE 0x04000 /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#define CONFIG_ENV_BUFFER_PRINT 1
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
-#define CFG_SYPCR 0xffffff89
+#define CONFIG_SYS_SYPCR 0xffffff89
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR 0x00610480
+#define CONFIG_SYS_SIUMCR 0x00610480
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
* power management and some other internal clocks
*/
#define SCCR_MASK 0x01800000
-#define CFG_SCCR 0x01800000
+#define CONFIG_SYS_SCCR 0x01800000
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
-#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/*
* FLASH timing: Default value of OR0 after reset
*/
-#define CFG_OR0_PRELIM 0xfe000954
-#define CFG_BR0_PRELIM 0xf0000401
+#define CONFIG_SYS_OR0_PRELIM 0xfe000954
+#define CONFIG_SYS_BR0_PRELIM 0xf0000401
/*
* BR1 and OR1 (SDRAM)
#define SDRAM_MAX_SIZE (64 << 20) /* max 64 MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CFG_OR_TIMING_SDRAM 0x00000A00
+#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-#define CFG_OR1_PRELIM 0xfc000800
-#define CFG_BR1_PRELIM (0x000000C0 | 0x01)
+#define CONFIG_SYS_OR1_PRELIM 0xfc000800
+#define CONFIG_SYS_BR1_PRELIM (0x000000C0 | 0x01)
-#define CFG_MPTPR 0x0200
+#define CONFIG_SYS_MPTPR 0x0200
/* PTB=16, AMB=001, FIXME 1 RAS precharge cycles, 1 READ loop cycle (not used),
1 Write loop Cycle (not used), 1 Timer Loop Cycle */
-#define CFG_MBMR 0x10964111
-#define CFG_MAR 0x00000088
+#define CONFIG_SYS_MBMR 0x10964111
+#define CONFIG_SYS_MAR 0x00000088
/*
* 4096 Rows from SDRAM example configuration
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
*/
-#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
/* GPIO/PIGGY on CS3 initialization values
*/
-#define CFG_PIGGY_BASE (0x30000000)
-#define CFG_OR3_PRELIM (0xfe000d24)
-#define CFG_BR3_PRELIM (0x30000401)
+#define CONFIG_SYS_PIGGY_BASE (0x30000000)
+#define CONFIG_SYS_OR3_PRELIM (0xfe000d24)
+#define CONFIG_SYS_BR3_PRELIM (0x30000401)
/*
* Internal Definitions
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
-#define OF_CPU "PowerPC,866@0"
-#define OF_SOC "soc@fff00000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc/cpm/serial@a80"
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define I2C_SOFT_DECLARATIONS
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_BASE_DIR ((u16 *)(CONFIG_SYS_PIGGY_BASE + 0x04))
+#define I2C_BASE_PORT ((u8 *)(CONFIG_SYS_PIGGY_BASE + 0x09))
+
+#define SDA_BIT 0x40
+#define SCL_BIT 0x80
+#define SDA_CONF 0x1000
+#define SCL_CONF 0x2000
+
+#define I2C_ACTIVE do {} while (0)
+#define I2C_TRISTATE do {} while (0)
+#define I2C_READ ((in_8(I2C_BASE_PORT) & SDA_BIT) == SDA_BIT)
+#define I2C_SDA(bit) if(bit) { \
+ clrbits(be16, I2C_BASE_DIR, SDA_CONF); \
+ } else { \
+ clrbits(8, I2C_BASE_PORT, SDA_BIT); \
+ setbits(be16, I2C_BASE_DIR, SDA_CONF); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ clrbits(be16, I2C_BASE_DIR, SCL_CONF); \
+ } else { \
+ clrbits(8, I2C_BASE_PORT, SCL_BIT); \
+ setbits(be16, I2C_BASE_DIR, SCL_CONF); \
+ }
+#define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */
+
+#define CONFIG_I2C_MULTI_BUS 1
+#define CONFIG_I2C_CMD_TREE 1
+#define CONFIG_SYS_MAX_I2C_BUS 2
+#define CONFIG_SYS_I2C_INIT_BOARD 1
+#define CONFIG_I2C_MUX 1
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* Support the IVM EEprom */
+#define CONFIG_SYS_IVM_EEPROM_ADR 0x50
+#define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400
+#define CONFIG_SYS_IVM_EEPROM_PAGE_LEN 0x100
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0, 2, 4, 6} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
+
+#define MTDIDS_DEFAULT "nor0=app"
+#define MTDPARTS_DEFAULT ( \
+ "mtdparts=app:384k(u-boot),128k(env),128k(envred),128k(free)," \
+ "1536k(esw0),8704k(rootfs0),1536k(esw1),2432k(rootfs1),640k(var),768k(cfg)")
+
#endif /* __CONFIG_H */