#define CONFIG_MPC8247 1
#define CONFIG_MPC8272_FAMILY 1
#define CONFIG_MGCOGE 1
+#define CONFIG_HOSTNAME mgcoge
#define CONFIG_CPM2 1 /* Has a CPM2 */
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+
/*
* Select serial console configuration
*
#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
#undef CONFIG_CONS_NONE /* It's not on external UART */
#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
+#define CONFIG_SYS_SMC_RXBUFLEN 128
+#define CONFIG_SYS_MAXIDLE 10
/*
* Select ethernet configuration
#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */
#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */
#undef CONFIG_ETHER_NONE /* No external Ethernet */
+#define CONFIG_NET_MULTI 1
#define CONFIG_ETHER_INDEX 4
-#define CFG_SCC_TOUT_LOOP 10000000
+#define CONFIG_SYS_SCC_TOUT_LOOP 10000000
-# define CFG_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
+# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
#ifndef CONFIG_8260_CLKIN
#define CONFIG_8260_CLKIN 66000000 /* in Hz */
#endif
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
+#define BOOTFLASH_START FE000000
+#define CONFIG_PRAM 512 /* protected RAM [KBytes] */
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
+#define MTDIDS_DEFAULT "nor0=boot,nor1=app"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=boot:384k(u-boot),128k(env),128k(envred),3456k(free);" \
+ "app:3m(esw0),10m(rootfs0),3m(esw1),10m(rootfs1),1m(var),5m(cfg)"
/*
* Default environment settings
*/
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "u-boot_addr=100000\0" \
- "kernel_addr=200000\0" \
- "fdt_addr=400000\0" \
- "rootpath=/opt/eldk-4.2/ppc_82xx\0" \
- "u-boot=/tftpboot/mgcoge/u-boot.bin\0" \
- "bootfile=/tftpboot/mgcoge/uImage\0" \
- "fdt_file=/tftpboot/mgcoge/mgcoge.dtb\0" \
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=prot off fe000000 fe03ffff; era fe000000 fe03ffff; " \
- "cp.b ${u-boot_addr} fe000000 ${filesize};" \
- "prot on fe000000 fe03ffff\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addcon=setenv bootargs ${bootargs} console=ttyCPM0,,${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:" \
- "${netmask}:${hostname}:${netdev}:off panic=1 " \
- "console=${console}\0" \
- "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcon;"\
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_self=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; " \
- "tftp ${ramdisk_addr} ${ramdisk_file}; " \
- "run ramargs addip; " \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "u-boot_addr=100000\0" \
+ "kernel_addr=200000\0" \
+ "fdt_addr=400000\0" \
+ "rootpath=/opt/eldk-4.2/ppc_82xx\0" \
+ "u-boot=/tftpboot/mgcoge/u-boot.bin\0" \
+ "bootfile=/tftpboot/mgcoge/uImage\0" \
+ "fdt_file=/tftpboot/mgcoge/mgcoge.dtb\0" \
+ "load=tftp ${u-boot_addr} ${u-boot}\0" \
+ "update=prot off fe000000 fe03ffff; era fe000000 fe03ffff; " \
+ "cp.b ${u-boot_addr} fe000000 ${filesize};" \
+ "prot on fe000000 fe03ffff\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addcons=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off panic=1\0" \
+ "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcons;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "net_self=tftp ${kernel_addr} ${bootfile}; " \
+ "tftp ${fdt_addr} ${fdt_file}; " \
+ "tftp ${ramdisk_addr} ${ramdisk_file}; " \
+ "run ramargs addip; " \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "EEprom_ivm=pca9544a:70:4 \0" \
+ "mtdparts=" MK_STR(MTDPARTS_DEFAULT) "\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_FLASH_BASE_1 0x50000000
+#define CONFIG_SYS_FLASH_SIZE_1 64
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 }
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFE000000
-#define CFG_FLASH_SIZE 32
-#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384KB for Monitor */
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
-#endif
+#define CONFIG_ENV_IS_IN_FLASH
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
-#define CFG_ENV_IS_IN_FLASH
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_BUFFER_PRINT 1
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-#endif /* CFG_ENV_IS_IN_FLASH */
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CFG_IMMR 0xF0000000
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CONFIG_I2C_MULTI_BUS 1
+#define CONFIG_I2C_CMD_TREE 1
+#define CONFIG_SYS_MAX_I2C_BUS 2
+#define CONFIG_SYS_I2C_INIT_BOARD 1
+#define CONFIG_I2C_MUX 1
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* Support the IVM EEprom */
+#define CONFIG_SYS_IVM_EEPROM_ADR 0x50
+#define CONFIG_SYS_IVM_EEPROM_MAX_LEN 0x400
+#define CONFIG_SYS_IVM_EEPROM_PAGE_LEN 0x100
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+#define CONFIG_SYS_IMMR 0xF0000000
+
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* Hard reset configuration word */
-#define CFG_HRCW_MASTER 0x0604b211
+#define CONFIG_SYS_HRCW_MASTER 0x0604b211
/* No slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID2 0
-#define CFG_SIUMCR 0x4020c200
-#define CFG_SYPCR 0xFFFFFFC3
-#define CFG_BCR 0x10000000
-#define CFG_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK)
+#define CONFIG_SYS_SIUMCR 0x4020c200
+#define CONFIG_SYS_SYPCR 0xFFFFFFC3
+#define CONFIG_SYS_BCR 0x10000000
+#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK)
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register 5-5
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
-#define CFG_RMR 0
+#define CONFIG_SYS_RMR 0
/*-----------------------------------------------------------------------
* TMCNTSC - Time Counter Status and Control 4-40
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* Init Memory Controller:
* ---- --- ------- ------ ------
* 0 60x GPCM 8 bit FLASH
* 1 60x SDRAM 32 bit SDRAM
+ * 3 60x GPCM 8 bit GPIO/PIGGY
+ * 5 60x GPCM 16 bit CFG-Flash
*
*/
/* Bank 0 - FLASH
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV2 |\
ORxG_SCY_5_CLK |\
/* Bank 1 - 60x bus SDRAM
*/
#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CFG_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-#define CFG_MPTPR 0x1800
+#define CONFIG_SYS_MPTPR 0x1800
/*-----------------------------------------------------------------------------
* Address for Mode Register Set (MRS) command
*-----------------------------------------------------------------------------
*/
-#define CFG_MRS_OFFS 0x00000110
-#define CFG_PSRT 0x0e
+#define CONFIG_SYS_MRS_OFFS 0x00000110
+#define CONFIG_SYS_PSRT 0x0e
-#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR1_PRELIM CFG_OR1
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1
/* SDRAM initialization values
*/
-#define CFG_OR1 ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_8 |\
ORxS_ROWST_PBI0_A7 |\
ORxS_NUMR_13)
-#define CFG_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
+#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
PSDMR_BSMA_A14_A16 |\
PSDMR_SDA10_PBI0_A9 |\
PSDMR_RFRC_5_CLK |\
PSDMR_WRC_1C |\
PSDMR_CL_2)
-#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
+/* GPIO/PIGGY on CS3 initialization values
+*/
+#define CONFIG_SYS_PIGGY_BASE 0x30000000
+#define CONFIG_SYS_PIGGY_SIZE 128
+
+#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_3_CLK | ORxG_TRLX )
+
+/* Board FPGA on CS4 initialization values
+*/
+#define CONFIG_SYS_FPGA_BASE 0x40000000
+#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/
+
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_3_CLK | ORxG_TRLX )
+
+/* CFG-Flash on CS5 initialization values
+*/
+#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\
+ BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_5_CLK | ORxG_TRLX )
+
+#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
/* pass open firmware flat tree */
+#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1