/*
* Serial console configuration
+ *
+ * To select console on the one of 8 external UARTs,
+ * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART,
+ * or as 5, 6, 7, or 8 for the second Quad UART.
+ * COM11, COM12, COM13, COM14 are located on the second Quad UART.
+ *
+ * CONFIG_PSC_CONSOLE must be undefined in this case.
+ */
+#ifdef CONFIG_CONSOLE_COM12
+#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */
+#else
+#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */
+#endif
+/*
+ * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1
+ * and undefine CONFIG_QUART_CONSOLE.
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+/*#define CONFIG_PSC_CONSOLE 1 */ /* console is on PSC1 */
+#if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE)
+#error "Select only one console device!"
+#endif
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
ADD_USB_CMD | \
CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
+ CFG_CMD_I2C)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
#define CFG_I2C_SPEED 100000 /* 100 kHz */
#define CFG_I2C_SLAVE 0x7F
-/*
- * EEPROM configuration
- */
-#define CFG_I2C_EEPROM_ADDR 0x58
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CFG_I2C_RTC_ADDR 0x51
-
/*
* Flash configuration (8,16 or 32 MB)
* TEXT base always at 0xFFF00000
#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
+#if TEXT_BASE == CFG_FLASH_BASE
+#define CFG_LOWBOOT 1
+#endif
+
/*
* Memory map
*/
/*
* GPIO configuration
*/
-//###CHD: MSB = 1 -> 64MB: funktioniert nicht: ERRATA - BUG?
-//###CHD: 0x10000004 = 32MB SDRAM
-//###CHD: 0x90000004 = 64MB SDRAM
-#define CFG_GPS_PORT_CONFIG 0x10000004
+/* 0x10000004 = 32MB SDRAM */
+/* 0x90000004 = 64MB SDRAM */
+#define CFG_GPS_PORT_CONFIG 0x00000004
/*
* Miscellaneous configurable options
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
+/* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */
+#define CFG_CS2_START 0x80000000
+#define CFG_CS2_SIZE 0x00001000
+#define CFG_CS2_CFG 0x1d300
+
+/* Second Quad UART @0x80010000 */
+#define CFG_CS1_START 0x80010000
+#define CFG_CS1_SIZE 0x00001000
+#define CFG_CS1_CFG 0x1d300
+
+/*
+ * Select one of quarts as a default
+ * console. If undefined - PSC console
+ * wil be default
+ */
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
#define CFG_RESET_ADDRESS 0xff000000
+/*
+ * QUART Expanders support
+ */
+#if defined(CONFIG_QUART_CONSOLE)
+/*
+ * We'll use NS16550 chip routines,
+ */
+#define CFG_NS16550 1
+#define CFG_NS16550_SERIAL 1
+#define CONFIG_CONS_INDEX 1
+/*
+ * To achieve necessary offset on SC16C554
+ * A0-A2 (register select) pins with NS16550
+ * functions (in struct NS16550), REG_SIZE
+ * should be 4, because A0-A2 pins are connected
+ * to DA2-DA4 address bus lines.
+ */
+#define CFG_NS16550_REG_SIZE 4
+/*
+ * LocalPlus Bus already inited in cpu_init_f(),
+ * so can work with QUART's chip selects.
+ * One of four SC16C554 UARTs is selected with
+ * A3-A4 (DA5-DA6) lines.
+ */
+#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5)
+#define CFG_NS16550_COM1 (CFG_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5)
+#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9)
+#define CFG_NS16550_COM1 (CFG_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5)
+#elif
+#error "Wrong QUART expander number."
+#endif
+
+/*
+ * SC16C554 chip's external crystal oscillator frequency
+ * is 7.3728 MHz
+ */
+#define CFG_NS16550_CLK 7372800
+#endif /* CONFIG_QUART_CONSOLE */
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------