#define CONFIG_DISPLAY_BOARDINFO_LATE
+#define CONFIG_MISC_INIT_R
+
#if defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
#define CONFIG_ENV_SECT_SIZE 0x40000
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
#define CONFIG_ENV_SIZE 0x20000
#endif
-#if defined(CONFIG_QSPI_BOOT)
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_QIXIS_I2C_ACCESS
#define SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#endif
#endif
+#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* QSPI device */
-#if defined(CONFIG_QSPI_BOOT)
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_FSL_QSPI
-#define CONFIG_SPI_FLASH_SPANSION
#define FSL_QSPI_FLASH_SIZE (1 << 26)
#define FSL_QSPI_FLASH_NUM 2
#endif
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
#define CONFIG_FSL_MEMAC
/* Initial environment variables */
#if defined(CONFIG_QSPI_BOOT)
+#define MC_INIT_CMD \
+ "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
+ "sf read 0x80100000 0xE00000 0x100000;" \
+ "env exists secureboot && " \
+ "sf read 0x80700000 0x700000 0x40000 && " \
+ "sf read 0x80740000 0x740000 0x40000 && " \
+ "esbc_validate 0x80700000 && " \
+ "esbc_validate 0x80740000 ;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000\0"
+#elif defined(CONFIG_SD_BOOT)
+#define MC_INIT_CMD \
+ "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
+ "mmc read 0x80100000 0x7000 0x800;" \
+ "env exists secureboot && " \
+ "mmc read 0x80700000 0x3800 0x10 && " \
+ "mmc read 0x80740000 0x3A00 0x10 && " \
+ "esbc_validate 0x80700000 && " \
+ "esbc_validate 0x80740000 ;" \
+ "fsl_mc start mc 0x80000000 0x80100000\0" \
+ "mcmemsize=0x70000000\0"
+#endif
+
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "BOARD=ls1088ardb\0" \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "loadaddr=0x90100000\0" \
- "kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x1000000\0" \
- "kernel_load=0xa0000000\0" \
+ "fdt_addr=0x64f00000\0" \
+ "kernel_addr=0x1000000\0" \
+ "kernel_addr_sd=0x8000\0" \
+ "kernelhdr_addr_sd=0x4000\0" \
+ "kernel_start=0x580100000\0" \
+ "kernelheader_start=0x580800000\0" \
+ "scriptaddr=0x80000000\0" \
+ "scripthdraddr=0x80080000\0" \
+ "fdtheader_addr_r=0x80100000\0" \
+ "kernelheader_addr=0x800000\0" \
+ "kernelheader_addr_r=0x80200000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "kernelheader_size=0x40000\0" \
+ "fdt_addr_r=0x90000000\0" \
+ "load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
- "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
- "sf read 0x80100000 0xE00000 0x100000;" \
- "fsl_mc start mc 0x80000000 0x80100000\0" \
- "mcmemsize=0x70000000 \0"
-
+ "kernel_size_sd=0x14000\0" \
+ "kernelhdr_size_sd=0x10\0" \
+ MC_INIT_CMD \
+ BOOTENV \
+ "boot_scripts=ls1088ardb_boot.scr\0" \
+ "boot_script_hdr=hdr_ls1088ardb_bs.out\0" \
+ "scan_dev_for_boot_part=" \
+ "part list ${devtype} ${devnum} devplist; " \
+ "env exists devplist || setenv devplist 1; " \
+ "for distro_bootpart in ${devplist}; do " \
+ "if fstype ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "bootfstype; then " \
+ "run scan_dev_for_boot; " \
+ "fi; " \
+ "done\0" \
+ "scan_dev_for_boot=" \
+ "echo Scanning ${devtype} " \
+ "${devnum}:${distro_bootpart}...; " \
+ "for prefix in ${boot_prefixes}; do " \
+ "run scan_dev_for_scripts; " \
+ "done;\0" \
+ "boot_a_script=" \
+ "load ${devtype} ${devnum}:${distro_bootpart} " \
+ "${scriptaddr} ${prefix}${script}; " \
+ "env exists secureboot && load ${devtype} " \
+ "${devnum}:${distro_bootpart} " \
+ "${scripthdraddr} ${prefix}${boot_script_hdr} " \
+ "&& esbc_validate ${scripthdraddr};" \
+ "source ${scriptaddr}\0" \
+ "installer=load mmc 0:2 $load_addr " \
+ "/flex_installer_arm64.itb; " \
+ "env exists mcinitcmd && run mcinitcmd && " \
+ "mmc read 0x80200000 0x6800 0x800;" \
+ "fsl_mc apply dpl 0x80200000;" \
+ "bootm $load_addr#ls1088ardb\0" \
+ "qspi_bootcmd=echo Trying load from qspi..;" \
+ "sf probe && sf read $load_addr " \
+ "$kernel_addr $kernel_size ; env exists secureboot " \
+ "&& sf read $kernelheader_addr_r $kernelheader_addr " \
+ "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
+ "bootm $load_addr#$BOARD\0" \
+ "sd_bootcmd=echo Trying load from sd card..;" \
+ "mmcinfo; mmc read $load_addr " \
+ "$kernel_addr_sd $kernel_size_sd ;" \
+ "env exists secureboot && mmc read $kernelheader_addr_r "\
+ "$kernelhdr_addr_sd $kernelhdr_size_sd " \
+ " && esbc_validate ${kernelheader_addr_r};" \
+ "bootm $load_addr#$BOARD\0"
+
+#undef CONFIG_BOOTCOMMAND
+#if defined(CONFIG_QSPI_BOOT)
+/* Try to boot an on-QSPI kernel first, then do normal distro boot */
+#define CONFIG_BOOTCOMMAND \
+ "sf read 0x80200000 0xd00000 0x100000;" \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && sf read 0x80780000 0x780000 0x100000 " \
+ "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ "&& fsl_mc apply dpl 0x80200000;" \
+ "run distro_bootcmd;run qspi_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
+
+/* Try to boot an on-SD kernel first, then do normal distro boot */
+#elif defined(CONFIG_SD_BOOT)
+#define CONFIG_BOOTCOMMAND \
+ "env exists mcinitcmd && mmcinfo; " \
+ "mmc read 0x80200000 0x6800 0x800; " \
+ "env exists mcinitcmd && env exists secureboot " \
+ " && mmc read 0x80780000 0x3800 0x10 " \
+ "&& esbc_validate 0x80780000;env exists mcinitcmd " \
+ "&& fsl_mc apply dpl 0x80200000;" \
+ "run distro_bootcmd;run sd_bootcmd;" \
+ "env exists secureboot && esbc_halt;"
#endif
/* MAC/PHY configuration */
#include <config_distro_defaults.h>
#define BOOT_TARGET_DEVICES(func) \
- func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
projects / oweals / u-boot.git / blobdiff