Merge branch 'master' of git://git.denx.de/u-boot-video

[oweals/u-boot.git] / include / configs / ls1043a_common.h

diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index 6b9856a18f4dc0a0e015b659e93a5dd2eb7c859c..54968b52312c7f7ee4a7de9eb119e5d793a00c23 100644 (file)
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -28,14 +28,6 @@
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #define CONFIG_BOARD_EARLY_INIT_F      1
 
-/* Flat Device Tree Definitions */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 #ifndef CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_FSL_DDR3            /* Use DDR3 memory */
 #endif
@@ -44,6 +36,7 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY      0
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
 
 #define CPU_RELEASE_ADDR               secondary_boot_func
 
@@ -120,6 +113,7 @@
 #endif
 
 /* IFC */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_FSL_IFC
 /*
  * CONFIG_SYS_FLASH_BASE has the final address (core view)
@@ -138,9 +132,9 @@
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS     45      /* count down from 45/5: 9..1 */
 #endif
+#endif
 
 /* I2C */
-#define CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1
@@ -180,30 +174,61 @@
 #endif
 
 /* Command line configuration */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
-#define CONFIG_CMD_PING
 
 /*  MMC  */
 #define CONFIG_MMC
 #ifdef CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_FAT
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 #define CONFIG_GENERIC_MMC
 #define CONFIG_DOS_PARTITION
 #endif
 
+/*  DSPI  */
+#define CONFIG_FSL_DSPI
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_DM_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO       /* cs0 */
+#define CONFIG_SPI_FLASH_SST           /* cs1 */
+#define CONFIG_SPI_FLASH_EON           /* cs2 */
+#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
+#define CONFIG_SF_DEFAULT_BUS          1
+#define CONFIG_SF_DEFAULT_CS           0
+#endif
+#endif
+
+#define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
+
 /* FMan ucode */
 #define CONFIG_SYS_DPAA_FMAN
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_FM_MURAM_SIZE       0x60000
 
+#ifdef CONFIG_NAND_BOOT
+/* Store Fman ucode at offeset 0x160000(11 blocks). */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR                (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SD_BOOT)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 1MB (2040 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820).
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR                (512 * 0x820)
+#elif defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR                0x400d0000
+#define CONFIG_ENV_SPI_BUS             0
+#define CONFIG_ENV_SPI_CS              0
+#define CONFIG_ENV_SPI_MAX_HZ          1000000
+#define CONFIG_ENV_SPI_MODE            0x03
+#else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 /* FMan fireware Pre-load address */
 #define CONFIG_SYS_FMAN_FW_ADDR                0x60300000
+#endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
 #define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif
@@ -225,24 +250,21 @@
        "ramdisk_size=0x2000000\0"              \
        "fdt_high=0xffffffffffffffff\0"         \
        "initrd_high=0xffffffffffffffff\0"      \
-       "kernel_start=0x61200000\0"             \
-       "kernel_load=0x807f0000\0"              \
-       "kernel_size=0x1000000\0"               \
+       "kernel_start=0x61100000\0"             \
+       "kernel_load=0xa0000000\0"              \
+       "kernel_size=0x2800000\0"               \
        "console=ttyAMA0,38400n8\0"
 
 #define CONFIG_BOOTARGS                        "console=ttyS0,115200 root=/dev/ram0 " \
-                                       "earlycon=uart8250,0x21c0500,115200"
+                                       "earlycon=uart8250,mmio,0x21c0500"
 #define CONFIG_BOOTCOMMAND             "cp.b $kernel_start $kernel_load "     \
                                        "$kernel_size && bootm $kernel_load"
 #define CONFIG_BOOTDELAY               10
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE              512     /* Console I/O Buffer Size */
-#define CONFIG_SYS_PROMPT              "=> "
 #define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
                                        sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING         1
@@ -251,4 +273,10 @@
 
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
+#endif
+
 #endif /* __LS1043A_COMMON_H */