#ifndef _CONFIG_KM_ARM_H
#define _CONFIG_KM_ARM_H
+/* We got removed from Linux mach-types.h */
+#define MACH_TYPE_KM_KIRKWOOD 2255
+
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_MARVELL
-#define CONFIG_ARM926EJS /* Basic Architecture */
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
#define CONFIG_KIRKWOOD /* SOC Family Name */
#define CONFIG_KW88F6281 /* SOC Name */
#define CONFIG_MACH_KM_KIRKWOOD /* Machine type */
+#define CONFIG_MACH_TYPE MACH_TYPE_KM_KIRKWOOD
+
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
-#define CONFIG_SYS_TEXT_BASE 0x04000000 /* code address after reloc */
-#define CONFIG_ENV_SIZE (128 << 10) /* NAND chip block size */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_SF
+#define CONFIG_SOFT_I2C /* I2C bit-banged */
+
+/* SPI NOR Flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED 8100000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
+
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 8100000
+#define CONFIG_ENV_SPI_MODE SPI_MODE_3
+#endif
+
+#include "asm/arch/config.h"
+
+#define CONFIG_SYS_TEXT_BASE 0x07d00000 /* code address before reloc */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
#define CONFIG_KM_CRAMFS_ADDR 0x2400000
#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 4096KBytes */
+/* architecture specific default bootargs */
+#define CONFIG_KM_DEF_BOOT_ARGS_CPU \
+ "bootcountaddr=${bootcountaddr} ${mtdparts}" \
+ " boardid=0x${IVM_BoardId} hwkey=0x${IVM_HWKey}"
+
#define CONFIG_KM_DEF_ENV_CPU \
- "addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "boot=bootm ${actual_kernel_addr} - -\0" \
- "cramfsloadfdt=echo \\\\c\0" \
- "tftpfdt=echo \\\\c\0" \
- CONFIG_KM_DEF_ENV_UPDATE \
+ "boot=bootm ${load_addr_r} - -\0" \
+ "cramfsloadfdt=true\0" \
+ "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.kwb\0" \
+ CONFIG_KM_UPDATE_UBOOT \
""
-
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#undef CONFIG_KIRKWOOD_PCIE_INIT /* Disable PCIE Port0 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-
#define CONFIG_MISC_INIT_R
/*
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE
/*
* Serial Port configuration
*/
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND
#define CONFIG_CMD_NFS
/*
* NAND Flash configuration
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_NAND_BASE 0xd8000000
#define BOOTFLASH_START 0x0
+/* Kirkwood has two serial IF */
+#if (CONFIG_CONS_INDEX == 2)
+#define CONFIG_KM_CONSOLE_TTY "ttyS1"
+#else
#define CONFIG_KM_CONSOLE_TTY "ttyS0"
+#endif
/*
* Other required minimal configurations
#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
/*
* Ethernet Driver configuration
*/
#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_CMD_MII /* to debug mdio phy config */
#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0
#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init 88E1118 PHY */
/*
* UBI related stuff
/*
* I2C related stuff
*/
-#define CONFIG_SOFT_I2C /* I2C bit-banged */
-
#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
#if defined(CONFIG_SOFT_I2C)
#ifndef __ASSEMBLY__
int get_scl(void);
#define KM_KIRKWOOD_SDA_PIN 8
#define KM_KIRKWOOD_SCL_PIN 9
+#define KM_KIRKWOOD_SOFT_I2C_GPIOS 0x0300
#define KM_KIRKWOOD_ENV_WP 38
#define I2C_ACTIVE __set_direction(KM_KIRKWOOD_SDA_PIN, 0)
#define I2C_SCL(bit) kw_gpio_set_value(KM_KIRKWOOD_SCL_PIN, bit)
#endif
-#define I2C_DELAY udelay(3) /* 1/4 I2C clock duration */
+#define I2C_DELAY udelay(1)
#define I2C_SOFT_DECLARATIONS
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_SPEED 100000
#endif
+/* EEprom support 24C128, 24C256 valid for environment eeprom */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 Byte write page */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* Environment variables configurations
*/
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_ENV_IS_IN_SPI_FLASH /* use SPI-Flash for environment vars */
+#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */
+#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */
+#else
#define CONFIG_ENV_IS_IN_EEPROM /* use EEPROM for environment vars */
#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_EEPROM_WREN
#define CONFIG_ENV_OFFSET 0x0 /* no bracets! */
-#undef CONFIG_ENV_SIZE
#define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET)
-#define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
-
-/* offset redund: (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS "\0"
#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif
-#define CONFIG_CMD_SF
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_SPI_FLASH
-#define CONFIG_HARD_SPI
-#define CONFIG_KIRKWOOD_SPI
#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50Mhz */
+
+/* SPI bus claim MPP configuration */
+#define CONFIG_SYS_KW_SPI_MPP 0x0
#define FLASH_GPIO_PIN 0x00010000
+#define KM_FLASH_GPIO_PIN 16
-#define MTDIDS_DEFAULT "nand0=orion_nand"
-/* test-only: partitioning needs some tuning, this is just for tests */
-#define MTDPARTS_DEFAULT "mtdparts=" \
- "orion_nand:" \
- "-(" CONFIG_KM_UBI_PARTITION_NAME ")"
+#ifndef MTDIDS_DEFAULT
+# define MTDIDS_DEFAULT "nand0=orion_nand"
+#endif /* MTDIDS_DEFAULT */
-#define CONFIG_KM_DEF_ENV_UPDATE \
+#ifndef MTDPARTS_DEFAULT
+# define MTDPARTS_DEFAULT "mtdparts=" \
+ "orion_nand:" \
+ "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
+#endif /* MTDPARTS_DEFAULT */
+
+#define CONFIG_KM_UPDATE_UBOOT \
"update=" \
- "spi on;sf probe 0;sf erase 0 50000;" \
- "sf write ${u-boot_addr_r} 0 ${filesize};" \
- "spi off\0"
+ "sf probe 0;sf erase 0 +${filesize};" \
+ "sf write ${load_addr_r} 0 ${filesize};\0"
+
+#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
+#define CONFIG_KM_NEW_ENV \
+ "newenv=sf probe 0;" \
+ "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
+ __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
+#else
+#define CONFIG_KM_NEW_ENV \
+ "newenv=setenv addr 0x100000 && " \
+ "i2c dev 1; mw.b ${addr} 0 4 && " \
+ "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \
+ " ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && " \
+ "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \
+ " ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0"
+#endif
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ CONFIG_KM_NEW_ENV \
+ "arch=arm\0" \
+ "EEprom_ivm=" KM_IVM_BUS "\0" \
+ ""
#if defined(CONFIG_SYS_NO_FLASH)
-#define CONFIG_KM_UBI_PARTITION_NAME "ubi0"
#undef CONFIG_FLASH_CFI_MTD
#undef CONFIG_JFFS2_CMDLINE
#endif
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
/* Do early setups now in board_init_f() */
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_KM_RESERVED_PRAM 0x801000
/* address for the bootcount (taken from end of RAM) */
#define BOOTCOUNT_ADDR (CONFIG_KM_RESERVED_PRAM)
+/* Use generic bootcount RAM driver */
+#define CONFIG_BOOTCOUNT_RAM
+
+/* enable POST tests */
+#define CONFIG_POST (CONFIG_SYS_POST_MEM_REGIONS)
+#define CONFIG_POST_SKIP_ENV_FLAGS
+#define CONFIG_POST_EXTERNAL_WORD_FUNCS
+#define CONFIG_CMD_DIAG
+
+/* we do the whole PCIe FPGA config stuff here */
+#define BOARD_LATE_INIT
#endif /* _CONFIG_KM_ARM_H */