/*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ * Grant Erickson <gerickson@nuovations.com>
+ *
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME kilauea
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_EMAC_COUNT
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_NAND_ADDR 0xF8000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */
-#define CFG_INIT_RAM_END (4 << 10)
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ * There are traditionally three options for the primordial
+ * (i.e. initial) stack usage on the 405-series:
+ *
+ * 1) On-chip Memory (OCM) (i.e. SRAM)
+ * 2) Data cache
+ * 3) SDRAM
+ *
+ * For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ * the latter of which is less than desireable since it requires
+ * setting up the SDRAM and ECC in assembly code.
+ *
+ * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ * select on the External Bus Controller (EBC) and then select a
+ * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
+ * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
+ * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ * physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CFG_INIT_DCACHE_CS 4
+
+#if defined(CFG_INIT_DCACHE_CS)
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
+#else
+#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16)
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CFG_INIT_DCACHE_CS)
+# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CFG_INIT_EXTRA_SIZE 16
+# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
+# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
+# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR
+#endif /* defined(CFG_INIT_DCACHE_CS) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif /* CFG_ENV_IS_IN_FLASH */
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 405EX the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from location 0xfffff000...0xffffffff the
+ * NAND controller cannot be accessed since it is attached to CS0 too.
+ */
+#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */
+#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */
+
+#define CFG_NAND_ECCSIZE 256
+#define CFG_NAND_ECCBYTES 3
+#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CFG_MBYTES_SDRAM (256) /* 256MB */
+#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \
+ SDRAM_RXBAS_SDSZ_256MB | \
+ SDRAM_RXBAS_SDAM_MODE7 | \
+ SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \
+ SDRAM_MCOPT1_8_BANKS | \
+ SDRAM_MCOPT1_DDR2_TYPE | \
+ SDRAM_MCOPT1_QDEP | \
+ SDRAM_MCOPT1_DCOO_DISABLED)
+#define CFG_SDRAM0_MCOPT2 0x00000000
+#define CFG_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \
+ SDRAM_MODT_EB0R_ENABLE)
+#define CFG_SDRAM0_MODT1 0x00000000
+#define CFG_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \
+ SDRAM_CODT_CKLZ_36OHM | \
+ SDRAM_CODT_DQS_1_8_V_DDR2 | \
+ SDRAM_CODT_IO_NMODE)
+#define CFG_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560)
+#define CFG_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(80) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP))
+#define CFG_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(3) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
+#define CFG_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL))
+#define CFG_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \
+ SDRAM_INITPLR_IMA_ENCODE(0))
+#define CFG_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \
+ JEDEC_MA_EMR_RTT_75OHM))
+#define CFG_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
+ JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
+ JEDEC_MA_MR_BLEN_4 | \
+ JEDEC_MA_MR_DLL_RESET))
+#define CFG_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(3) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
+ SDRAM_INITPLR_IBA_ENCODE(0x0) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
+#define CFG_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(26) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
+#define CFG_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(26) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
+#define CFG_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(26) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
+#define CFG_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(26) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
+#define CFG_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
+ JEDEC_MA_MR_CL_DDR2_4_0_CLK | \
+ JEDEC_MA_MR_BLEN_4))
+#define CFG_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER | \
+ JEDEC_MA_EMR_RDQS_DISABLE | \
+ JEDEC_MA_EMR_DQS_DISABLE | \
+ JEDEC_MA_EMR_RTT_DISABLED | \
+ JEDEC_MA_EMR_ODS_NORMAL))
+#define CFG_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \
+ SDRAM_INITPLR_IMWT_ENCODE(2) | \
+ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
+ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
+ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \
+ JEDEC_MA_EMR_RDQS_DISABLE | \
+ JEDEC_MA_EMR_DQS_DISABLE | \
+ JEDEC_MA_EMR_RTT_DISABLED | \
+ JEDEC_MA_EMR_ODS_NORMAL))
+#define CFG_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE)
+#define CFG_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE)
+#define CFG_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \
+ SDRAM_RQDC_RQFD_ENCODE(56))
+#define CFG_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521)
+#define CFG_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2)
+#define CFG_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \
+ SDRAM_DLCR_DLCS_CONT_DONE | \
+ SDRAM_DLCR_DLCV_ENCODE(165))
+#define CFG_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV)
+#define CFG_SDRAM0_WRDTR 0x00000000
+#define CFG_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \
+ SDRAM_SDTR1_RTW_2_CLK | \
+ SDRAM_SDTR1_RTRO_1_CLK)
+#define CFG_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \
+ SDRAM_SDTR2_WTR_2_CLK | \
+ SDRAM_SDTR2_XSNR_32_CLK | \
+ SDRAM_SDTR2_WPC_4_CLK | \
+ SDRAM_SDTR2_RPC_2_CLK | \
+ SDRAM_SDTR2_RP_3_CLK | \
+ SDRAM_SDTR2_RRD_2_CLK)
+#define CFG_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \
+ SDRAM_SDTR3_RC_ENCODE(11) | \
+ SDRAM_SDTR3_XCS | \
+ SDRAM_SDTR3_RFC_ENCODE(26))
+#define CFG_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \
+ SDRAM_MMODE_DCL_DDR2_4_0_CLK | \
+ SDRAM_MMODE_BLEN_4)
+#define CFG_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \
+ SDRAM_MEMODE_RTT_75OHM)
+
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 2
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=kilauea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty;" \
- "bootm 200000\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=kilauea/uImage\0" \
- "fdt_file=kilauea/kilauea.dtb\0" \
- "fdt_addr=400000\0" \
"kernel_addr=fc000000\0" \
+ "fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 kilauea/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CACHE | \
+#define CONFIG_POST (CFG_POST_CACHE | \
CFG_POST_CPU | \
CFG_POST_ETHER | \
CFG_POST_I2C | \
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+/* booting from NAND, so NAND chips select has to be on CS 0 */
+#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+
+/* Memory Bank 1 (NOR-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x05806500
+#define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x018003c0
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000)
+#else
#define CFG_NAND_CS 1 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
/* Memory Bank 1 (NAND-FLASH) initialization */
#define CFG_EBC_PB1AP 0x018003c0
#define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000)
+#endif
/* Memory Bank 2 (FPGA) initialization */
#define CFG_EBC_PB2AP 0x9400C800
-#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2CR (CFG_FPGA_BASE | 0x18000)
#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */
-/*-----------------------------------------------------------------------
- * NAND FLASH
- *----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3] - EBC data 0-3 inputs/outputs
- * GPIO0[4-7] - USB data 4-7 inputs/outputs
- * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15] - USB data 0-3 inputs/outputs
- * GPIO0[16-21] - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26] - Instruction trace outputs
- * GPIO0[28] - Float, N/C
- * GPIO0[29-31] - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL 0x00AA54AA
-#define CFG_GPIO0_OSRH 0x21800000
-#define CFG_GPIO0_TSRL 0x00AA55AA
-#define CFG_GPIO0_TSRH 0xA5A00000
-
-#define CFG_GPIO0_ISR1L 0x00000100
-#define CFG_GPIO0_ISR1H 0x04000000
-#define CFG_GPIO0_ISR2L 0x00550055
-#define CFG_GPIO0_ISR2H 0x40100000
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
+{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \
+} \
+}
/*-----------------------------------------------------------------------
* Some Kilauea stuff..., mainly fpga registers
*/
#define CFG_FPGA_REG_BASE CFG_FPGA_BASE
-#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 11))
+#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 10))
/* interrupt */
#define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000
#define CFG_FPGA_USER_LED1 0x00000100
#endif /* __CONFIG_H */
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,405EX@0"