#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_440SPE 1 /* Specifc SPe support */
-#undef CFG_DRAM_TEST /* Disable-takes long time */
+#define CONFIG_440SPE_REVA 1 /* Support old Rev A. */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
+
+/*
+ * Enable this board for more than 2GB of SDRAM
+ */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_VERY_BIG_RAM
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME katmai
+#include "amcc-common.h"
+
+/*
+ * For booting 256K-paged Linux we should have 16MB of memory
+ * for Linux initial memory map
+ */
+#undef CONFIG_SYS_BOOTMAPSZ
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#undef CONFIG_SHOW_BOOT_PROGRESS
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
-#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
-
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
-#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
-
-#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
-#define CFG_PCIE_MEMSIZE 0x01000000
-#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
-
-#define CFG_PCIE0_CFGBASE 0xc0000000
-#define CFG_PCIE1_CFGBASE 0xc1000000
-#define CFG_PCIE2_CFGBASE 0xc2000000
-#define CFG_PCIE0_XCFGBASE 0xc3000000
-#define CFG_PCIE1_XCFGBASE 0xc3001000
-#define CFG_PCIE2_XCFGBASE 0xc3002000
+#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */
+#define CONFIG_SYS_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
+#define CONFIG_SYS_ISRAM_BASE 0x90000000 /* internal SRAM */
+
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
+#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
+
+#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
+#define CONFIG_SYS_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
+
+#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
+#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
+#define CONFIG_SYS_PCIE2_CFGBASE 0xc2000000
+#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
+#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
+#define CONFIG_SYS_PCIE2_XCFGBASE 0xc3002000
+
+/* base address of inbound PCIe window */
+#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL
/* System RAM mapped to PCI space */
-#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
-#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_BUS CONFIG_SYS_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS CONFIG_SYS_SDRAM_BASE
#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
-#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
+#define CONFIG_SYS_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
-#define CFG_TEMP_STACK_OCM 1
-#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
-#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
-#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
-#undef CFG_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK
/*-----------------------------------------------------------------------
* DDR SDRAM
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC 1 /* with ECC support */
+#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/
#undef CONFIG_STRESS
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */
+#define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */
#define IIC0_BOOTPROM_ADDR 0x50
#define IIC0_ALT_BOOTPROM_ADDR 0x54
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0x50)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0x50)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C bootstrap EEPROM */
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
+#define CONFIG_4xx_CONFIG_BLOCKSIZE 8
/* I2C RTC */
#define CONFIG_RTC_M41T11 1
-#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */
-#define CFG_I2C_RTC_ADDR 0x68
-#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */
+#define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */
/* I2C DTT */
#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
-#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */
+#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
/*
* standard dtt sensor configuration - bottom bit will determine local or
* remote sensor of the ADM1021, the rest determines index into
- * CFG_DTT_ADM1021 array below.
+ * CONFIG_SYS_DTT_ADM1021 array below.
*/
#define CONFIG_DTT_SENSORS { 0, 1 }
* - local temp sensor enabled, min set to 0 deg, max set to 85 deg
* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
*/
-#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
+#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
+#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=katmai\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=katmai/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 katmai/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b ${fileaddr} fffc0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
"kozio=bootm ffc60000\0" \
"pciconfighost=1\0" \
+ "pcie_mode=RP:RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ECCTEST
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-
+#define CONFIG_CMD_SNTP
#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT /* let board init pci target */
-#undef CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
+#undef CONFIG_SYS_PCI_MASTER_INIT
-#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+/* #define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_DEVICEID */
/*
* NETWORK Support (PCI):
* Xilinx System ACE support
*----------------------------------------------------------------------*/
#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */
-#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
-#define CFG_SYSTEMACE_BASE CFG_ACE_BASE
+#define CONFIG_SYS_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
+#define CONFIG_SYS_SYSTEMACE_BASE CONFIG_SYS_ACE_BASE
#define CONFIG_DOS_PARTITION 1
/*-----------------------------------------------------------------------
*----------------------------------------------------------------------*/
/* Memory Bank 0 (Flash) initialization */
-#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
+#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(7) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED)
-#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | \
+#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT)
/* Memory Bank 1 (Xilinx System ACE controller) initialization */
-#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
+#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(4) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_SOR_NONDELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED)
-#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \
+#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_ACE_BASE) | \
EBC_BXCR_BS_1MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT)
* Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
* default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
*-------------------------------------------------------------------------*/
-#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK | \
+#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_UNLOCK | \
EBC_CFG_PTD_ENABLE | \
EBC_CFG_RTC_16PERCLK | \
EBC_CFG_ATC_PREVIOUS | \
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-#define CFG_GPIO_PCIE_PRESENT0 17
-#define CFG_GPIO_PCIE_PRESENT1 21
-#define CFG_GPIO_PCIE_PRESENT2 23
-#define CFG_GPIO_RS232_FORCEOFF 30
-
-#define CFG_PFC0 (GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) | \
- GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) | \
- GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) | \
- GPIO_VAL(CFG_GPIO_RS232_FORCEOFF))
-#define CFG_GPIO_OR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
-#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
-#define CFG_GPIO_ODR 0
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
+#define CONFIG_SYS_GPIO_PCIE_PRESENT0 17
+#define CONFIG_SYS_GPIO_PCIE_PRESENT1 21
+#define CONFIG_SYS_GPIO_PCIE_PRESENT2 23
+#define CONFIG_SYS_GPIO_RS232_FORCEOFF 30
+
+#define CONFIG_SYS_PFC0 (GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT0) | \
+ GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT1) | \
+ GPIO_VAL(CONFIG_SYS_GPIO_PCIE_PRESENT2) | \
+ GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF))
+#define CONFIG_SYS_GPIO_OR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)
+#define CONFIG_SYS_GPIO_TCR GPIO_VAL(CONFIG_SYS_GPIO_RS232_FORCEOFF)
+#define CONFIG_SYS_GPIO_ODR 0
#endif /* __CONFIG_H */