mx53evk: Place machine ID into board config

[oweals/u-boot.git] / include / configs / innokom.h

diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 043ae2f364a270f49e91cff3a880856f8aca08b2..2e4b3463748dd314c355b9b157c9fbb8d8f9da32 100644 (file)
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -39,6 +39,12 @@
 
 #undef CONFIG_USE_IRQ                  /* we don't need IRQ/FIQ stuff      */
                                        /* for timer/console/ethernet       */
+
+#define        CONFIG_SYS_TEXT_BASE    0x0
+
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_DCACHE_OFF
+
 /*
  * Hardware drivers
  */
@@ -46,6 +52,7 @@
 /*
  * select serial console configuration
  */
+#define CONFIG_PXA_SERIAL
 #define CONFIG_FFUART          1       /* we use FFUART on CSB226 */
 
 /* allow to overwrite serial and ethaddr */
@@ -103,7 +110,6 @@
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN          (256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE       128             /* size in bytes reserved for initial data */
 
 #define CONFIG_SYS_LONGHELP                            /* undef to save memory         */
 #define CONFIG_SYS_PROMPT              "uboot> "       /* Monitor Command Prompt       */
@@ -115,8 +121,6 @@
 #define CONFIG_SYS_MEMTEST_START       0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa3000000      /* load kernel to this address   */
 
 #define CONFIG_SYS_HZ                  1000
@@ -136,6 +140,8 @@
 /*
  * I2C bus
  */
+#define CONFIG_I2C_MV                  1
+#define CONFIG_MV_I2C_REG              0x40301680
 #define CONFIG_HARD_I2C                        1
 #define CONFIG_SYS_I2C_SPEED                   50000
 #define CONFIG_SYS_I2C_SLAVE                   0xfe
@@ -154,7 +160,8 @@
 /*
  * SMSC91C111 Network Card
  */
-#define CONFIG_DRIVER_SMC91111         1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111                1
 #define CONFIG_SMC91111_BASE           0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT                     /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY                  /* we use internal phy   */
@@ -188,6 +195,9 @@
 
 #define CONFIG_SYS_FLASH_BASE          PHYS_FLASH_1
 
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM_1
+#define        CONFIG_SYS_INIT_SP_ADDR         (GENERATED_GBL_DATA_SIZE + PHYS_SDRAM_1)
+
 /*
  * JFFS2 partitions
  *
@@ -340,6 +350,9 @@
  */
 #define CONFIG_SYS_PSSR_VAL            0x37
 
+#define        CONFIG_SYS_CCCR                 CCCR_L27|CCCR_M2|CCCR_N10
+#define        CONFIG_SYS_CKEN                 0x0
+
 /*
  * Memory settings
  *
@@ -473,6 +486,9 @@
 #define CONFIG_SYS_MCIO0_VAL           0x00000000
 #define CONFIG_SYS_MCIO1_VAL           0x00000000
 
+#define        CONFIG_SYS_FLYCNFG_VAL          0x00000000
+#define        CONFIG_SYS_SXCNFG_VAL           0x00000000
+
 /*
 #define CSB226_USER_LED0       0x00000008
 #define CSB226_USER_LED1       0x00000010