/*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EXT2 | \
- CFG_CMD_FAT | \
- CFG_CMD_IDE | \
- CFG_CMD_PCI | \
- CFG_CMD_USB )
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
+#define CONFIG_ETHADDR 00:a0:a4:03:00:00
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+#define CONFIG_IPADDR 192.168.100.2
+#define CONFIG_SERVERIP 192.168.100.1
+#define CONFIG_NETMASK 255.255.255.0
+#define HOSTNAME inka4x0
+#define CONFIG_BOOTFILE /tftpboot/inka4x0/uImage
+#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=ttyS0,${baudrate}\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};" \
+ "run nfsargs addip addcons;bootm\0" \
+ "enable_disp=mw.l 100000 04000000 1;" \
+ "cp.l 100000 f0000b20 1;" \
+ "cp.l 100000 f0000b28 1\0" \
+ "ideargs=setenv bootargs root=/dev/hda1 rw\0" \
+ "ide_boot=ext2load ide 0:1 200000 uImage;" \
+ "run ideargs addip addcons enable_disp;bootm\0" \
+ "brightness=255\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
+#define CONFIG_BOOTCOMMAND "run ide_boot"
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE 0xFFE00000
-
-#define CFG_FLASH_SIZE 0x00200000 /* 2 MByte */
-#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */
-
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) /* second sector */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
- (= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CFG_FLASH_BASE 0xffe00000
+#define CFG_FLASH_SIZE 0x00200000
+#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/*
* Environment settings
*/
#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000)
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_OVERWRITE 1
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
/*
* Memory map
#define CFG_SDRAM_BASE 0x00000000
#define CFG_DEFAULT_MBAR 0x80000000
-#define CONFIG_MPC5200_DDR
+/*
+ * SDRAM controller configuration
+ */
+#undef CONFIG_SDR_MT48LC16M16A2
+#undef CONFIG_DDR_MT46V16M16
+#undef CONFIG_DDR_MT46V32M16
+#undef CONFIG_DDR_HYB25D512160BF
+#define CONFIG_DDR_K4H511638C
/* Use ON-Chip SRAM until RAM will be available */
#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
# define CFG_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
*/
/* #define CONFIG_FEC_10MBIT 1 */
#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII
/*
* GPIO configuration
*
- * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
- * Bit 0 (mask: 0x80000000): 1
+ * use CS1 as gpio_wkup_6 output
+ * Bit 0 (mask: 0x80000000): 0
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
* 00 -> No Alternatives, I2C1 is used for onboard EEPROM
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
* use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
* 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- * tests.
*/
-#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG 0x93000004
-#else
-#define CFG_GPS_PORT_CONFIG 0x81001004
-#endif
+#define CFG_GPS_PORT_CONFIG 0x01001004
/*
* RTC configuration
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/* Enable an alternate, more extensive memory test */
#define CFG_ALT_MEMTEST
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
*/
#define CONFIG_LOOPW
#define CFG_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000
-
#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
-
-/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
-
-/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
-
-/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CFG_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */
+#define CFG_ATA_STRIDE 4 /* Interval between registers */
#define CONFIG_ATAPI 1
+#define CFG_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */
+
#endif /* __CONFIG_H */