#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/*
* Serial console configuration
*/
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_ISO_PARTITION
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
* Command line configuration.
*/
#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
"cp.l 100000 f0000b28 1\0" \
"ideargs=setenv bootargs root=/dev/hda1 rw\0" \
"ide_boot=ext2load ide 0:1 200000 uImage;" \
- "run ideargs addip addcons enable_disp;bootm" \
+ "run ideargs addip addcons enable_disp;bootm\0" \
"brightness=255\0" \
""
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE 0xFFE00000
-
-#define CFG_FLASH_SIZE 0x00200000 /* 2 MByte */
-#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */
-
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) /* second sector */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
- (= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1
+#define CFG_FLASH_BASE 0xffe00000
+#define CFG_FLASH_SIZE 0x00200000
+#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/*
* Environment settings
*/
#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000)
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x2000
#define CONFIG_ENV_OVERWRITE 1
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
/*
* Memory map
#define CFG_SDRAM_BASE 0x00000000
#define CFG_DEFAULT_MBAR 0x80000000
-#define CONFIG_MPC5200_DDR
+/*
+ * SDRAM controller configuration
+ */
+#undef CONFIG_SDR_MT48LC16M16A2
+#undef CONFIG_DDR_MT46V16M16
+#undef CONFIG_DDR_MT46V32M16
+#undef CONFIG_DDR_HYB25D512160BF
+#define CONFIG_DDR_K4H511638C
/* Use ON-Chip SRAM until RAM will be available */
#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
# define CFG_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
*/
#define CONFIG_LOOPW