/*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* (easy to change)
*/
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
-#define CONFIG_INKA4X0 1 /* INKA4x0 board */
+#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
+#define CONFIG_INKA4X0 1 /* INKA4x0 board */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Serial console configuration
*/
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
+#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
+#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+/*
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ */
+#define CONFIG_PCI 1
+#define CONFIG_PCI_PNP 1
+#define CONFIG_PCI_SCAN_SHOW 1
+
+#define CONFIG_PCI_MEM_BUS 0x40000000
+#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
+#define CONFIG_PCI_MEM_SIZE 0x10000000
+
+#define CONFIG_PCI_IO_BUS 0x50000000
+#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
+#define CONFIG_PCI_IO_SIZE 0x01000000
+
+#define CFG_XLB_PIPELINING 1
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
/*
* Supported commands
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_EXT2 | \
+ CFG_CMD_FAT | \
+ CFG_CMD_IDE | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_SNTP | \
+ CFG_CMD_USB )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
+
#if (TEXT_BASE == 0xFFE00000) /* Boot low */
# define CFG_LOWBOOT 1
#endif
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
#undef CONFIG_BOOTARGS
+#define CONFIG_ETHADDR 00:a0:a4:03:00:00
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+#define CONFIG_IPADDR 192.168.100.2
+#define CONFIG_SERVERIP 192.168.100.1
+#define CONFIG_NETMASK 255.255.255.0
+#define HOSTNAME inka4x0
+#define CONFIG_BOOTFILE /tftpboot/inka4x0/uImage
+#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
- "bootfile=uImage\0" \
- "serverip=192.168.1.1\0" \
- "ipaddr=192.168.160.2\0" \
- "ethaddr=00:00:1A:1B:CE:AF\0" \
- "dk=tftp 100000 inka4x0/u-boot.dk;protect off all;erase ffe00000 ffe2ffff;cp.b 100000 ffe00000 $(filesize)\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=ttyS0,${baudrate}\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};" \
+ "run nfsargs addip addcons;bootm\0" \
+ "enable_disp=mw.l 100000 04000000 1;" \
+ "cp.l 100000 f0000b20 1;" \
+ "cp.l 100000 f0000b28 1\0" \
+ "ideargs=setenv bootargs root=/dev/hda1 rw\0" \
+ "ide_boot=ext2load ide 0:1 200000 uImage;" \
+ "run ideargs addip addcons enable_disp;bootm" \
+ "brightness=255\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
+#define CONFIG_BOOTCOMMAND "run ide_boot"
/*
* IPB Bus clocking configuration.
*/
/* #define CONFIG_FEC_10MBIT 1 */
#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII
/*
* GPIO configuration
*
- * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
- * Bit 0 (mask: 0x80000000): 1
+ * use CS1 as gpio_wkup_6 output
+ * Bit 0 (mask: 0x80000000): 0
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
* 00 -> No Alternatives, I2C1 is used for onboard EEPROM
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
* use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
* 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- * tests.
*/
-#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG 0x93000004
-#else
-#define CFG_GPS_PORT_CONFIG 0x83000004
-#endif
+#define CFG_GPS_PORT_CONFIG 0x01001004
/*
* RTC configuration
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
+/* 32Mbit SRAM @0x30000000 */
+#define CFG_CS1_START 0x30000000
+#define CFG_CS1_SIZE 0x00400000
+#define CFG_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */
+
+/* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */
+#define CFG_CS2_START 0x80000000
+#define CFG_CS2_SIZE 0x0001000
+#define CFG_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */
+
+/* GPIO in @0x30400000 */
+#define CFG_CS3_START 0x30400000
+#define CFG_CS3_SIZE 0x00100000
+#define CFG_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */
+
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
+/*-----------------------------------------------------------------------
+ * USB stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_CLOCK 0x00015555
+#define CONFIG_USB_CONFIG 0x00001000
+#define CONFIG_USB_STORAGE
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_PREINIT
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CFG_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */
+#define CFG_ATA_STRIDE 4 /* Interval between registers */
+
+#define CONFIG_ATAPI 1
+
+#define CFG_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */
+
#endif /* __CONFIG_H */