*/
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
+#define CONFIG_OMAP_GPIO
#define CONFIG_SDRC /* The chip has SDRC controller */
#define CONFIG_CMD_FAT /* FAT support */
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
+#ifdef CONFIG_BOOT_ONENAND
#define CONFIG_CMD_ONENAND /* ONENAND support */
+#endif
+#ifdef CONFIG_BOOT_NAND
+#define CONFIG_CMD_NAND
+#endif
#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
"usbtty=cdc_acm\0" \
"loadaddr=0x82000000\0" \
"usbtty=cdc_acm\0" \
- "console=ttyS2,115200n8\0" \
- "mpurate=500\0" \
+ "console=ttyO2,115200n8\0" \
+ "mpurate=auto\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext3 rootwait\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
"nandroot=/dev/mtdblock4 rw\0" \
"nandrootfstype=jffs2\0" \
"mmcargs=setenv bootargs console=${console} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
+ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t $loadaddr $filesize\0" \
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc rescan ${mmcdev}; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadbootenv; then " \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loaduimage; then " \
+ "run mmcboot;" \
+ "fi;" \
+ "fi;" \
+ "run nandboot;" \
#define CONFIG_AUTO_COMPLETE 1
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "U-Boot # "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
-/*
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-
/*
* Physical Memory Map
*
* FLASH and environment organization
*/
+#ifdef CONFIG_BOOT_ONENAND
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M /* Configure the PISMO */
#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
#define CONFIG_ENV_IS_IN_ONENAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET
+#endif
+
+#ifdef CONFIG_BOOT_NAND
+#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_BASE NAND_BASE
+#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
+#define CONFIG_ENV_ADDR NAND_ENV_OFFSET
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#endif
/*
* Size of malloc() pool
#define CONFIG_SMC911X_BASE 0x2C000000
#endif /* (CONFIG_CMD_NET) */
+/*
+ * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
+ * and older u-boot.bin with the new U-Boot SPL.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80008000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
+/* SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE 0x40200800
+#define CONFIG_SPL_MAX_SIZE (54 * 1024)
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+/* move malloc and bss high to prevent clashing with the main image */
+#define CONFIG_SYS_SPL_MALLOC_START 0x87000000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
+#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+/* MMC boot config */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+#ifdef CONFIG_BOOT_ONENAND
+#define CONFIG_SPL_ONENAND_SUPPORT
+
+/* OneNAND boot config */
+#define CONFIG_SYS_ONENAND_U_BOOT_OFFS 0x80000
+#define CONFIG_SYS_ONENAND_PAGE_SIZE 2048
+#define CONFIG_SPL_ONENAND_LOAD_ADDR 0x80000
+#define CONFIG_SPL_ONENAND_LOAD_SIZE \
+ (512 * 1024 - CONFIG_SPL_ONENAND_LOAD_ADDR)
+
+#endif
+
+#ifdef CONFIG_BOOT_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#endif
+
#endif /* __IGEP00X0_H */