#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * Stuff still to be dealt with -
- */
-#define CONFIG_RTC_MC146818
-
/*
* High Level Configuration Options
* (easy to change)
*/
-#define DEBUG_PARSER
-
-#define CONFIG_X86 1 /* Intel X86 CPU */
-#define CONFIG_SYS_SC520 1 /* AMD SC520 */
+#define CONFIG_SYS_SC520
#define CONFIG_SYS_SC520_SSI
-#define CONFIG_SHOW_BOOT_PROGRESS 1
-#define CONFIG_LAST_STAGE_INIT 1
+#define CONFIG_SHOW_BOOT_PROGRESS
+#define CONFIG_LAST_STAGE_INIT
-/*
- * If CONFIG_HW_WATCHDOG is not defined, the watchdog jumper on the
+/*-----------------------------------------------------------------------
+ * Watchdog Configuration
+ * NOTE: If CONFIG_HW_WATCHDOG is NOT defined, the watchdog jumper on the
* bottom (processor) board MUST be removed!
*/
#undef CONFIG_WATCHDOG
#define CONFIG_HW_WATCHDOG
- /*-----------------------------------------------------------------------
- * Serial Configuration
- */
+/*-----------------------------------------------------------------------
+ * Real Time Clock Configuration
+ */
+#define CONFIG_RTC_MC146818
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0
+
+/*-----------------------------------------------------------------------
+ * Serial Configuration
+ */
#define CONFIG_SERIAL_MULTI
-#define CONFIG_CONS_INDEX 1
+#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK 1843200
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1 UART0_BASE
-#define CONFIG_SYS_NS16550_COM2 UART1_BASE
-#define CONFIG_SYS_NS16550_COM3 (0x1000 + UART0_BASE)
-#define CONFIG_SYS_NS16550_COM4 (0x1000 + UART1_BASE)
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK 1843200
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_SYS_BAUDRATE_TABLE {300, 600, 1200, 2400, 4800, \
+ 9600, 19200, 38400, 115200}
+#define CONFIG_SYS_NS16550_COM1 UART0_BASE
+#define CONFIG_SYS_NS16550_COM2 UART1_BASE
+#define CONFIG_SYS_NS16550_COM3 (0x1000 + UART0_BASE)
+#define CONFIG_SYS_NS16550_COM4 (0x1000 + UART1_BASE)
#define CONFIG_SYS_NS16550_PORT_MAPPED
- /*-----------------------------------------------------------------------
- * Video Configuration
- */
-#undef CONFIG_VIDEO /* No Video Hardware */
-#undef CONFIG_CFB_CONSOLE
-
-/*
- * Size of malloc() pool
+/*-----------------------------------------------------------------------
+ * Video Configuration
*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#undef CONFIG_VIDEO
+#undef CONFIG_CFB_CONSOLE
/*-----------------------------------------------------------------------
* Command line configuration.
*/
#include <config_cmd_default.h>
-#define CONFIG_CMD_BDI /* bdinfo */
-#define CONFIG_CMD_BOOTD /* bootd */
-#define CONFIG_CMD_CONSOLE /* coninfo */
-#define CONFIG_CMD_ECHO /* echo arguments */
-#define CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#define CONFIG_CMD_FPGA /* FPGA configuration Support */
-#define CONFIG_CMD_IMI /* iminfo */
-#define CONFIG_CMD_IMLS /* List all found images */
-#define CONFIG_CMD_IRQ /* IRQ Information */
-#define CONFIG_CMD_ITEST /* Integer (and string) test */
-#define CONFIG_CMD_LOADB /* loadb */
-#define CONFIG_CMD_LOADS /* loads */
-#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
-#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-#undef CONFIG_CMD_NFS /* NFS support */
-#define CONFIG_CMD_PCI /* PCI support */
-#define CONFIG_CMD_PING /* ICMP echo support */
-#define CONFIG_CMD_RUN /* run command in env variable */
-#define CONFIG_CMD_SAVEENV /* saveenv */
-#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-#define CONFIG_CMD_SOURCE /* "source" command Support */
-#define CONFIG_CMD_XIMG /* Load part of Multi Image */
-
-#define CONFIG_BOOTDELAY 15
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
-/* #define CONFIG_BOOTCOMMAND "bootm 38000000" */
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ITEST
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_SOURCE
+#define CONFIG_CMD_XIMG
+
+#define CONFIG_BOOTDELAY 15
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#define CONFIG_KGDB_BAUDRATE 115200
+#define CONFIG_KGDB_SER_INDEX 2
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + \
- 16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_HZ 1000 /* incrementer freq: 1kHz */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "boot > "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + \
+ 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000
+#define CONFIG_SYS_MEMTEST_END 0x01000000
+#define CONFIG_SYS_LOAD_ADDR 0x100000
+#define CONFIG_SYS_HZ 1000
/*-----------------------------------------------------------------------
* SDRAM Configuration
*/
-#define CONFIG_SYS_SDRAM_DRCTMCTL 0x18
-#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_SYS_SDRAM_DRCTMCTL 0x18
+#define CONFIG_SYS_SDRAM_REFRESH_RATE 156
+#define CONFIG_NR_DRAM_BANKS 4
/* CONFIG_SYS_SDRAM_DRCTMCTL Overrides the following*/
#undef CONFIG_SYS_SDRAM_PRECHARGE_DELAY
-#undef CONFIG_SYS_SDRAM_REFRESH_RATE
#undef CONFIG_SYS_SDRAM_RAS_CAS_DELAY
#undef CONFIG_SYS_SDRAM_CAS_LATENCY_2T
#undef CONFIG_SYS_SDRAM_CAS_LATENCY_3T
/*-----------------------------------------------------------------------
* CPU Features
*/
-#define CONFIG_SYS_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
-#define CONFIG_SYS_SC520_RESET /* use SC520 MMCR's to reset cpu */
-#define CONFIG_SYS_SC520_TIMER /* use SC520 swtimers */
-#undef CONFIG_SYS_GENERIC_TIMER /* use the i8254 PIT timers */
-#undef CONFIG_SYS_TSC_TIMER /* use the Pentium TSC timers */
-#define CONFIG_SYS_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
- * in the SC520 on the CDP */
+#define CONFIG_SYS_SC520_HIGH_SPEED 0
+#define CONFIG_SYS_SC520_RESET
+#define CONFIG_SYS_SC520_TIMER
+#undef CONFIG_SYS_GENERIC_TIMER
#define CONFIG_SYS_PCAT_INTERRUPTS
-#define CONFIG_SYS_NUM_IRQS 16
+#define CONFIG_SYS_NUM_IRQS 16
/*-----------------------------------------------------------------------
- * Memory organization
+ * Memory organization:
+ * 32kB Stack
+ * 16kB Cache-As-RAM @ 0x19200000
+ * 256kB Monitor
+ * (128kB + Environment Sector Size) malloc pool
*/
-#define CONFIG_SYS_STACK_SIZE 0x8000 /* Size of bootloader stack */
-#define CONFIG_SYS_BL_START_FLASH 0x38040000 /* Address of relocated code */
-#define CONFIG_SYS_BL_START_RAM 0x03fd0000 /* Address of relocated code */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_FLASH_BASE 0x38000000 /* Boot Flash */
-#define CONFIG_SYS_FLASH_BASE_1 0x10000000 /* StrataFlash 1 */
-#define CONFIG_SYS_FLASH_BASE_2 0x11000000 /* StrataFlash 2 */
+#define CONFIG_SYS_STACK_SIZE (32 * 1024)
+#define CONFIG_SYS_CAR_ADDR 0x19200000
+#define CONFIG_SYS_CAR_SIZE (16 * 1024)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_CAR_ADDR + \
+ CONFIG_SYS_CAR_SIZE)
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SECT_SIZE + \
+ 128*1024)
+/* Address of temporary Global Data */
+#define CONFIG_SYS_INIT_GD_ADDR CONFIG_SYS_CAR_ADDR
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
- /*-----------------------------------------------------------------------
- * FLASH configuration
- */
-#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
+/*-----------------------------------------------------------------------
+ * FLASH configuration
+ * 512kB Boot Flash @ 0x38000000 (Monitor @ 38040000)
+ * 16MB StrataFlash #1 @ 0x10000000
+ * 16MB StrataFlash #2 @ 0x11000000
+ */
+#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_FLASH_CFI_LEGACY
-#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
- CONFIG_SYS_FLASH_BASE_1, \
- CONFIG_SYS_FLASH_BASE_2}
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_MAX_FLASH_BANKS 3
+#define CONFIG_SYS_FLASH_BASE 0x38000000
+#define CONFIG_SYS_FLASH_BASE_1 0x10000000
+#define CONFIG_SYS_FLASH_BASE_2 0x11000000
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \
+ CONFIG_SYS_FLASH_BASE_1, \
+ CONFIG_SYS_FLASH_BASE_2}
#define CONFIG_SYS_FLASH_EMPTY_INFO
#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_SYS_MAX_FLASH_SECT 128
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_SYS_FLASH_LEGACY_512Kx8
+#define CONFIG_SYS_FLASH_ERASE_TOUT 2000 /* ms */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 2000 /* ms */
+
+/*-----------------------------------------------------------------------
+ * Environment configuration
+ * - Boot flash is 512kB with 64kB sectors
+ * - StrataFlash is 32MB with 128kB sectors
+ * - Redundant embedded environment is 25% of the Boot flash
+ * - Redundant StrataFlash environment is <1% of the StrataFlash
+ * - Environment is therefore located in StrataFlash
+ * - Primary copy is located in first sector of first flash
+ * - Redundant copy is located in second sector of first flash
+ * - Stack is only 32kB, so environment size is limited to 4kB
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x01000
+#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE_1
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE_1 + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+
+/*-----------------------------------------------------------------------
+ * PCI configuration
+ */
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_SYS_FIRST_PCI_IRQ 10
+#define CONFIG_SYS_SECOND_PCI_IRQ 9
+#define CONFIG_SYS_THIRD_PCI_IRQ 11
+#define CONFIG_SYS_FORTH_PCI_IRQ 15
- /*-----------------------------------------------------------------------
- * Environment configuration
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE_1
-/* Redundant Copy */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE_1 + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SECT_SIZE
-
-
- /*-----------------------------------------------------------------------
- * PCI configuration
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_PNP /* pci plug-and-play */
-#define CONFIG_SYS_FIRST_PCI_IRQ 10
-#define CONFIG_SYS_SECOND_PCI_IRQ 9
-#define CONFIG_SYS_THIRD_PCI_IRQ 11
-#define CONFIG_SYS_FORTH_PCI_IRQ 15
-
- /*
+/*-----------------------------------------------------------------------
* Network device (TRL8100B) support
*/
#define CONFIG_NET_MULTI
#define CONFIG_RTL8139
/*-----------------------------------------------------------------------
- * FPGA configuration
- */
-#define CONFIG_SYS_FPGA_PROGRAM_PIO_BIT 0x2000
-#define CONFIG_SYS_FPGA_INIT_PIO_BIT 0x4000
-#define CONFIG_SYS_FPGA_DONE_PIO_BIT 0x8000
-#define CONFIG_SYS_FPGA_PIO_DATA SC520_PIODATA31_16
-#define CONFIG_SYS_FPGA_PIO_DIRECTION SC520_PIODIR31_16
-#define CONFIG_SYS_FPGA_PIO_CLR SC520_PIOCLR31_16
-#define CONFIG_SYS_FPGA_PIO_SET SC520_PIOSET31_16
-#define CONFIG_SYS_FPGA_PROGRAM_BIT_DROP_TIME 1 /* milliseconds */
-#define CONFIG_SYS_FPGA_MAX_INIT_TIME 10 /* milliseconds */
-#define CONFIG_SYS_FPGA_MAX_FINALISE_TIME 10 /* milliseconds */
-#define CONFIG_SYS_FPGA_SSI_DATA_RATE 8333 /* kHz (33.3333MHz xtal) */
-
-#ifndef __ASSEMBLER__
-extern unsigned long ip;
-
-#define PRINTIP asm ("call 0\n" \
- "0:\n" \
- "pop %%eax\n" \
- "movl %%eax, %0\n" \
- :"=r"(ip) \
- : /* No Input Registers */ \
- :"%eax"); \
- printf("IP: 0x%08lx (File: %s, Line: %d)\n", ip, __FILE__, __LINE__);
+ * BOOTCS Control (for AM29LV040B-120JC)
+ *
+ * 000 0 00 0 000 11 0 011 }- 0x0033
+ * \ / | \| | \ / \| | \ /
+ * | | | | | | | |
+ * | | | | | | | +---- 3 Wait States (First Access)
+ * | | | | | | +------- Reserved
+ * | | | | | +--------- 3 Wait States (Subsequent Access)
+ * | | | | +------------- Reserved
+ * | | | +---------------- Non-Paged Mode
+ * | | +------------------ 8 Bit Wide
+ * | +--------------------- GP Bus
+ * +------------------------ Reserved
+ */
+#define CONFIG_SYS_SC520_BOOTCS_CTRL 0x0033
+
+/*-----------------------------------------------------------------------
+ * ROMCS Control (for E28F128J3A-150 StrataFlash)
+ *
+ * 000 0 01 1 000 01 0 101 }- 0x0615
+ * \ / | \| | \ / \| | \ /
+ * | | | | | | | |
+ * | | | | | | | +---- 5 Wait States (First Access)
+ * | | | | | | +------- Reserved
+ * | | | | | +--------- 1 Wait State (Subsequent Access)
+ * | | | | +------------- Reserved
+ * | | | +---------------- Paged Mode
+ * | | +------------------ 16 Bit Wide
+ * | +--------------------- GP Bus
+ * +------------------------ Reserved
+ */
+#define CONFIG_SYS_SC520_ROMCS1_CTRL 0x0615
+#define CONFIG_SYS_SC520_ROMCS2_CTRL 0x0615
+
+/*-----------------------------------------------------------------------
+ * SC520 General Purpose Bus configuration
+ *
+ * Chip Select Offset 1 Clock Cycle
+ * Chip Select Pulse Width 8 Clock Cycles
+ * Chip Select Read Offset 2 Clock Cycles
+ * Chip Select Read Width 6 Clock Cycles
+ * Chip Select Write Offset 2 Clock Cycles
+ * Chip Select Write Width 6 Clock Cycles
+ * Chip Select Recovery Time 2 Clock Cycles
+ *
+ * Timing Diagram (from SC520 Register Set Manual - Order #22005B)
+ *
+ * |<-------------General Purpose Bus Cycle---------------->|
+ * | |
+ * ----------------------\__________________/------------------
+ * |<--(GPCSOFF + 1)-->|<--(GPCSPW + 1)-->|<-(GPCSRT + 1)-> |
+ *
+ * ------------------------\_______________/-------------------
+ * |<---(GPRDOFF + 1)--->|<-(GPRDW + 1)->|
+ *
+ * --------------------------\_______________/-----------------
+ * |<----(GPWROFF + 1)---->|<-(GPWRW + 1)->|
+ *
+ * ________/-----------\_______________________________________
+ * |<--->|<--------->|
+ * ^ ^
+ * (GPALEOFF + 1) |
+ * |
+ * (GPALEW + 1)
+ */
+#define CONFIG_SYS_SC520_GPCSOFF 0x00
+#define CONFIG_SYS_SC520_GPCSPW 0x07
+#define CONFIG_SYS_SC520_GPRDOFF 0x01
+#define CONFIG_SYS_SC520_GPRDW 0x05
+#define CONFIG_SYS_SC520_GPWROFF 0x01
+#define CONFIG_SYS_SC520_GPWRW 0x05
+#define CONFIG_SYS_SC520_GPCSRT 0x01
+
+/*-----------------------------------------------------------------------
+ * SC520 Programmable I/O configuration
+ *
+ * Pin Mode Dir. Description
+ * ----------------------------------------------------------------------
+ * PIO0 PIO Output Unused
+ * PIO1 GPBHE# Output GP Bus Byte High Enable (active low)
+ * PIO2 PIO Output Auxiliary power output enable
+ * PIO3 GPAEN Output GP Bus Address Enable
+ * PIO4 PIO Output Top Board Enable (active low)
+ * PIO5 PIO Output StrataFlash 16 bit mode (low = 8 bit mode)
+ * PIO6 PIO Input Data output of Power Supply ADC
+ * PIO7 PIO Output Clock input to Power Supply ADC
+ * PIO8 PIO Output Chip Select input of Power Supply ADC
+ * PIO9 PIO Output StrataFlash 1 Reset / Power Down (active low)
+ * PIO10 PIO Output StrataFlash 2 Reset / Power Down (active low)
+ * PIO11 PIO Input StrataFlash 1 Status
+ * PIO12 PIO Input StrataFlash 2 Status
+ * PIO13 GPIRQ10# Input Can Bus / I2C IRQ (active low)
+ * PIO14 PIO Input Low Input Voltage Warning (active low)
+ * PIO15 PIO Output Watchdog (must toggle at least every 1.6s)
+ * PIO16 PIO Input Power Fail
+ * PIO17 GPIRQ6 Input Compact Flash 1 IRQ (active low)
+ * PIO18 GPIRQ5 Input Compact Flash 2 IRQ (active low)
+ * PIO19 GPIRQ4# Input Dual-Port RAM IRQ (active low)
+ * PIO20 GPIRQ3 Input UART D IRQ
+ * PIO21 GPIRQ2 Input UART C IRQ
+ * PIO22 GPIRQ1 Input UART B IRQ
+ * PIO23 GPIRQ0 Input UART A IRQ
+ * PIO24 GPDBUFOE# Output GP Bus Data Bus Buffer Output Enable
+ * PIO25 PIO Input Battery OK Indication
+ * PIO26 GPMEMCS16# Input GP Bus Memory Chip-Select 16-bit access
+ * PIO27 GPCS0# Output SRAM 1 Chip Select
+ * PIO28 PIO Input Top Board UART CTS
+ * PIO29 PIO Output FPGA Program Mode (active low)
+ * PIO30 PIO Input FPGA Initialised (active low)
+ * PIO31 PIO Input FPGA Done (active low)
+ */
+#define CONFIG_SYS_SC520_PIOPFS15_0 0x200a
+#define CONFIG_SYS_SC520_PIOPFS31_16 0x0dfe
+#define CONFIG_SYS_SC520_PIODIR15_0 0x87bf
+#define CONFIG_SYS_SC520_PIODIR31_16 0x2900
+
+/*-----------------------------------------------------------------------
+ * PIO Pin defines
+ */
+#define CONFIG_SYS_ENET_AUX_PWR 0x0004
+#define CONFIG_SYS_ENET_TOP_BRD_PWR 0x0010
+#define CONFIG_SYS_ENET_SF_WIDTH 0x0020
+#define CONFIG_SYS_ENET_PWR_ADC_DATA 0x0040
+#define CONFIG_SYS_ENET_PWR_ADC_CLK 0x0080
+#define CONFIG_SYS_ENET_PWR_ADC_CS 0x0100
+#define CONFIG_SYS_ENET_SF1_MODE 0x0200
+#define CONFIG_SYS_ENET_SF2_MODE 0x0400
+#define CONFIG_SYS_ENET_SF1_STATUS 0x0800
+#define CONFIG_SYS_ENET_SF2_STATUS 0x1000
+#define CONFIG_SYS_ENET_PWR_STATUS 0x4000
+#define CONFIG_SYS_ENET_WATCHDOG 0x8000
+
+#define CONFIG_SYS_ENET_PWR_FAIL 0x0001
+#define CONFIG_SYS_ENET_BAT_OK 0x0200
+#define CONFIG_SYS_ENET_TOP_BRD_CTS 0x1000
+#define CONFIG_SYS_ENET_FPGA_PROG 0x2000
+#define CONFIG_SYS_ENET_FPGA_INIT 0x4000
+#define CONFIG_SYS_ENET_FPGA_DONE 0x8000
+
+/*-----------------------------------------------------------------------
+ * Chip Select Pin Function Select
+ *
+ * 1 1 1 1 1 0 0 0 }- 0xf8
+ * | | | | | | | |
+ * | | | | | | | +--- Reserved
+ * | | | | | | +----- GPCS1_SEL = ROMCS1#
+ * | | | | | +------- GPCS2_SEL = ROMCS2#
+ * | | | | +--------- GPCS3_SEL = GPCS3
+ * | | | +----------- GPCS4_SEL = GPCS4
+ * | | +------------- GPCS5_SEL = GPCS5
+ * | +--------------- GPCS6_SEL = GPCS6
+ * +----------------- GPCS7_SEL = GPCS7
+ */
+#define CONFIG_SYS_SC520_CSPFS 0xf8
+
+/*-----------------------------------------------------------------------
+ * Clock Select (CLKTIMER[CLKTEST] pin)
+ *
+ * 0 111 00 1 0 }- 0x72
+ * | \ / \| | |
+ * | | | | +--- Pin Disabled
+ * | | | +----- Pin is an output
+ * | | +------- Reserved
+ * | +----------- Disabled (pin stays Low)
+ * +-------------- Reserved
+ */
+#define CONFIG_SYS_SC520_CLKSEL 0x72
+
+/*-----------------------------------------------------------------------
+ * Address Decode Control
+ *
+ * 0 00 0 0 0 0 0 }- 0x00
+ * | \| | | | | |
+ * | | | | | | +--- Integrated UART 1 is enabled
+ * | | | | | +----- Integrated UART 2 is enabled
+ * | | | | +------- Integrated RTC is enabled
+ * | | | +--------- Reserved
+ * | | +----------- I/O Hole accesses are forwarded to the external GP bus
+ * | +------------- Reserved
+ * +---------------- Write-protect violations do not generate an IRQ
+ */
+#define CONFIG_SYS_SC520_ADDDECCTL 0x00
+
+/*-----------------------------------------------------------------------
+ * UART Control
+ *
+ * 00000 1 1 1 }- 0x07
+ * \___/ | | |
+ * | | | +--- Transmit TC interrupt enable
+ * | | +----- Receive TC interrupt enable
+ * | +------- 1.8432 MHz
+ * +----------- Reserved
+ */
+#define CONFIG_SYS_SC520_UART1CTL 0x07
+#define CONFIG_SYS_SC520_UART2CTL 0x07
+
+/*-----------------------------------------------------------------------
+ * System Arbiter Control
+ *
+ * 00000 1 1 0 }- 0x06
+ * \___/ | | |
+ * | | | +--- Disable PCI Bus Arbiter Grant Time-Out Interrupt
+ * | | +----- The system arbiter operates in concurrent mode
+ * | +------- Park the PCI bus on the last master that acquired the bus
+ * +----------- Reserved
+ */
+#define CONFIG_SYS_SC520_SYSARBCTL 0x06
+
+/*-----------------------------------------------------------------------
+ * System Arbiter Master Enable
+ *
+ * 00000000000 0 0 0 1 1 }- 0x06
+ * \_________/ | | | | |
+ * | | | | | +--- PCI master REQ0 enabled (Ethernet 1)
+ * | | | | +----- PCI master REQ1 enabled (Ethernet 2)
+ * | | | +------- PCI master REQ2 disabled
+ * | | +--------- PCI master REQ3 disabled
+ * | +----------- PCI master REQ4 disabled
+ * +------------------ Reserved
+ */
+#define CONFIG_SYS_SC520_SYSARBMENB 0x0003
+
+/*-----------------------------------------------------------------------
+ * System Arbiter Master Enable
+ *
+ * 0 0000 0 00 0000 1 000 }- 0x06
+ * | \__/ | \| \__/ | \_/
+ * | | | | | | +---- Reserved
+ * | | | | | +------- Enable CPU-to-PCI bus write posting
+ * | | | | +---------- Reserved
+ * | | | +-------------- PCI bus reads to SDRAM are not automatically
+ * | | | retried
+ * | | +----------------- Target read FIFOs are not snooped during write
+ * | | transactions
+ * | +-------------------- Reserved
+ * +------------------------ Deassert the PCI bus reset signal
+ */
+#define CONFIG_SYS_SC520_HBCTL 0x08
+
+/*-----------------------------------------------------------------------
+ * PAR for Boot Flash - 512kB @ 0x38000000, BOOTCS
+ * 100 0 1 0 1 00000000111 11100000000000 }- 0x8a01f800
+ * \ / | | | | \----+----/ \-----+------/
+ * | | | | | | +---------- Start at 0x38000000
+ * | | | | | +----------------------- 512kB Region Size
+ * | | | | | ((7 + 1) * 64kB)
+ * | | | | +------------------------------ 64kB Page Size
+ * | | | +-------------------------------- Writes Enabled (So it can be
+ * | | | reprogrammed!)
+ * | | +---------------------------------- Caching Disabled
+ * | +------------------------------------ Execution Enabled
+ * +--------------------------------------- BOOTCS
+ */
+#define CONFIG_SYS_SC520_BOOTCS_PAR 0x8a01f800
+
+/*-----------------------------------------------------------------------
+ * Cache-As-RAM (Targets Boot Flash)
+ *
+ * 100 1 0 0 0 0001111 011001001000000000 }- 0x903d9200
+ * \ / | | | | \--+--/ \-------+--------/
+ * | | | | | | +------------ Start at 0x19200000
+ * | | | | | +------------------------- 64k Region Size
+ * | | | | | ((15 + 1) * 4kB)
+ * | | | | +------------------------------ 4kB Page Size
+ * | | | +-------------------------------- Writes Enabled
+ * | | +---------------------------------- Caching Enabled
+ * | +------------------------------------ Execution Prevented
+ * +--------------------------------------- BOOTCS
+ */
+#define CONFIG_SYS_SC520_CAR_PAR 0x903d9200
+
+/*-----------------------------------------------------------------------
+ * PAR for Low Level I/O (LEDs, Hex Switches etc) - 33 Bytes @ 0x1000, GPCS6
+ *
+ * 001 110 0 000100000 0001000000000000 }- 0x38201000
+ * \ / \ / | \---+---/ \------+-------/
+ * | | | | +----------- Start at 0x00001000
+ * | | | +------------------------ 33 Bytes (0x20 + 1)
+ * | | +------------------------------ Ignored
+ * | +--------------------------------- GPCS6
+ * +------------------------------------- GP Bus I/O
+ */
+#define CONFIG_SYS_SC520_LLIO_PAR 0x38201000
+
+/*-----------------------------------------------------------------------
+ * PAR for Compact Flash Port #1 - 4kB @ 0x200000000, CS5
+ * PAR for Compact Flash Port #2 - 4kB @ 0x200010000, CS7
+ *
+ * 010 101 0 0000000 100000000000000000 }- 0x54020000
+ * 010 111 0 0000000 100000000000000001 }- 0x5c020001
+ * \ / \ / | \--+--/ \-------+--------/
+ * | | | | +------------ Start at 0x200000000
+ * | | | | 0x200010000
+ * | | | +------------------------- 4kB Region Size
+ * | | | ((0 + 1) * 4kB)
+ * | | +------------------------------ 4k Page Size
+ * | +--------------------------------- GPCS5
+ * | GPCS7
+ * +------------------------------------- GP Bus Memory
+ */
+#define CONFIG_SYS_SC520_CF1_PAR 0x54020000
+#define CONFIG_SYS_SC520_CF2_PAR 0x5c020001
+
+/*-----------------------------------------------------------------------
+ * PAR for Extra 16550 UART A - 8 bytes @ 0x013f8, GPCS0
+ * PAR for Extra 16550 UART B - 8 bytes @ 0x012f8, GPCS3
+ * PAR for Extra 16550 UART C - 8 bytes @ 0x011f8, GPCS4
+ * PAR for Extra 16550 UART D - 8 bytes @ 0x010f8, GPCS5
+ *
+ * 001 000 0 000000111 0001001111111000 }- 0x200713f8
+ * 001 011 0 000000111 0001001011111000 }- 0x2c0712f8
+ * 001 011 0 000000111 0001001011111000 }- 0x300711f8
+ * 001 011 0 000000111 0001001011111000 }- 0x340710f8
+ * \ / \ / | \---+---/ \------+-------/
+ * | | | | +----------- Start at 0x013f8
+ * | | | | 0x012f8
+ * | | | | 0x011f8
+ * | | | | 0x010f8
+ * | | | +------------------------ 33 Bytes (32 + 1)
+ * | | +------------------------------ Ignored
+ * | +--------------------------------- GPCS6
+ * +------------------------------------- GP Bus I/O
+ */
+#define CONFIG_SYS_SC520_UARTA_PAR 0x200713f8
+#define CONFIG_SYS_SC520_UARTB_PAR 0x2c0712f8
+#define CONFIG_SYS_SC520_UARTC_PAR 0x300711f8
+#define CONFIG_SYS_SC520_UARTD_PAR 0x340710f8
+
+/*-----------------------------------------------------------------------
+ * PAR for StrataFlash #1 - 16MB @ 0x10000000, ROMCS1
+ * PAR for StrataFlash #2 - 16MB @ 0x11000000, ROMCS2
+ *
+ * 101 0 1 0 1 00011111111 01000000000000 }- 0xaa3fd000
+ * 110 0 1 0 1 00011111111 01000100000000 }- 0xca3fd100
+ * \ / | | | | \----+----/ \-----+------/
+ * | | | | | | +---------- Start at 0x10000000
+ * | | | | | | 0x11000000
+ * | | | | | +----------------------- 16MB Region Size
+ * | | | | | ((255 + 1) * 64kB)
+ * | | | | +------------------------------ 64kB Page Size
+ * | | | +-------------------------------- Writes Enabled
+ * | | +---------------------------------- Caching Disabled
+ * | +------------------------------------ Execution Enabled
+ * +--------------------------------------- ROMCS1
+ * ROMCS2
+ */
+#define CONFIG_SYS_SC520_SF1_PAR 0xaa3fd000
+#define CONFIG_SYS_SC520_SF2_PAR 0xca3fd100
+
+/*-----------------------------------------------------------------------
+ * PAR for SRAM #1 - 1MB @ 0x19000000, GPCS0
+ * PAR for SRAM #2 - 1MB @ 0x19100000, GPCS3
+ *
+ * 010 000 1 00000001111 01100100000000 }- 0x4203d900
+ * 010 011 1 00000001111 01100100010000 }- 0x4e03d910
+ * \ / \ / | \----+----/ \-----+------/
+ * | | | | +---------- Start at 0x19000000
+ * | | | | 0x19100000
+ * | | | +----------------------- 1MB Region Size
+ * | | | ((15 + 1) * 64kB)
+ * | | +------------------------------ 64kB Page Size
+ * | +--------------------------------- GPCS0
+ * | GPCS3
+ * +------------------------------------- GP Bus Memory
+ */
+#define CONFIG_SYS_SC520_SRAM1_PAR 0x4203d900
+#define CONFIG_SYS_SC520_SRAM2_PAR 0x4e03d910
+
+/*-----------------------------------------------------------------------
+ * PAR for Dual-Port RAM - 4kB @ 0x18100000, GPCS4
+ *
+ * 010 100 0 00000000 11000000100000000 }- 0x50018100
+ * \ / \ / | \---+--/ \-------+-------/
+ * | | | | +----------- Start at 0x18100000
+ * | | | +------------------------ 4kB Region Size
+ * | | | ((0 + 1) * 4kB)
+ * | | +------------------------------ 4kB Page Size
+ * | +--------------------------------- GPCS4
+ * +------------------------------------- GP Bus Memory
+ */
+#define CONFIG_SYS_SC520_DPRAM_PAR 0x50018100
-#endif
#endif /* __CONFIG_H */