powerpc/85xx: Fix NAND SPL support

[oweals/u-boot.git] / include / configs / digsy_mtc.h

diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h
index bfbec6a8603f65a659a7358a81578332fc13eadd..d0d1eda608c4aa3074a62d900114eb82daa35f7e 100644 (file)
--- a/include/configs/digsy_mtc.h
+++ b/include/configs/digsy_mtc.h
@@ -70,6 +70,7 @@
 #define CONFIG_PCI             1
 #define CONFIG_PCI_PNP         1
 #define CONFIG_PCI_SCAN_SHOW   1
+#define CONFIG_PCI_BOOTDELAY   250
 
 #define CONFIG_PCI_MEM_BUS     0x40000000
 #define CONFIG_PCI_MEM_PHYS    CONFIG_PCI_MEM_BUS
@@ -85,11 +86,39 @@
 #define CONFIG_DOS_PARTITION
 #define CONFIG_BZIP2
 
+/*
+ * Video
+ */
+#define CONFIG_VIDEO
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_MB862xx
+#define CONFIG_VIDEO_MB862xx_ACCEL
+#define CONFIG_VIDEO_CORALP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)       /* decompressed img */
+
+/* Coral-PA clock frequency, geo and other both 133MHz */
+#define CONFIG_SYS_MB862xx_CCF 0x00050000
+/* Video SDRAM parameters */
+#define CONFIG_SYS_MB862xx_MMR 0x11d7fa72
+#endif
+
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
 #define CONFIG_CMD_DFL
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DATE
@@ -252,12 +281,21 @@
 #if defined(CONFIG_DIGSY_REV5)
 #define CONFIG_SYS_I2C_RTC_ADDR        0x56
 #define CONFIG_RTC_RV3029
+/* Enable 5k Ohm trickle charge resistor */
+#define CONFIG_SYS_RV3029_TCR  0x20
 #else
 #define CONFIG_RTC_DS1337
 #define CONFIG_SYS_I2C_RTC_ADDR        0x68
 #define CONFIG_SYS_DS1339_TCR_VAL      0xAB    /* diode + 4k resistor */
 #endif
 
+/* ExBo I2C Addresses */
+#if defined(CONFIG_DIGSY_REV5)
+#define CONFIG_SYS_EXBO_EE_I2C_ADDRESS 0x54
+#else
+#define CONFIG_SYS_EXBO_EE_I2C_ADDRESS 0x56
+#endif
+
 /*
  * Flash configuration
  */
@@ -268,8 +306,8 @@
 #define CONFIG_SYS_FLASH_BASE          0xFE000000
 #define CONFIG_SYS_FLASH_BASE_CS1      0xFC000000
 #define CONFIG_SYS_MAX_FLASH_BANKS     2
-#define CONFIG_SYS_FLASH_BANKS_LIST    { CONFIG_SYS_FLASH_BASE_CS1, \
-                                       CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_FLASH_BANKS_LIST    { CONFIG_SYS_FLASH_BASE, \
+                                       CONFIG_SYS_FLASH_BASE_CS1}
 #define CONFIG_SYS_UPDATE_FLASH_SIZE
 #define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
 #else
@@ -343,7 +381,11 @@
  */
 #define CONFIG_MPC5xxx_FEC     1
 #define CONFIG_MPC5xxx_FEC_MII100
+#if defined(CONFIG_DIGSY_REV5)
+#define CONFIG_PHY_ADDR                0x01
+#else
 #define CONFIG_PHY_ADDR                0x00
+#endif
 #define CONFIG_PHY_RESET_DELAY 1000
 
 #define CONFIG_NETCONSOLE              /* include NetConsole support   */