/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 256*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
#endif
#define CONFIG_HARD_I2C 1 /* required for DA9030 access */
-#define CFG_I2C_SPEED 400000 /* I2C speed */
-#define CFG_I2C_SLAVE 1 /* I2C controllers address */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
+#define CONFIG_SYS_I2C_SLAVE 1 /* I2C controllers address */
#define DA9030_I2C_ADDR 0x49 /* I2C address of DA9030 */
-#define CFG_DA9030_EXTON_DELAY 100000 /* wait x us after DA9030 reset via EXTON */
-#define CFG_I2C_INIT_BOARD 1
+#define CONFIG_SYS_DA9030_EXTON_DELAY 100000 /* wait x us after DA9030 reset via EXTON */
+#define CONFIG_SYS_I2C_INIT_BOARD 1
/* #define CONFIG_HW_WATCHDOG 1 /\* Required for hitting the DA9030 WD *\/ */
#define DELTA_CHECK_KEYBD 1 /* check for keys pressed during boot */
#define CONFIG_BAUDRATE 115200
-/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
#ifdef TURN_ON_ETHERNET
-# define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING)
+
+#define CONFIG_CMD_PING
+
#else
-# define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_ENV \
- | CFG_CMD_NAND \
- | CFG_CMD_I2C) \
- & ~(CFG_CMD_NET \
- | CFG_CMD_FLASH \
- | CFG_CMD_IMLS))
+
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_I2C
+
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+
#endif
+/* USB */
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_USB_STORAGE 1
+#define CONFIG_DOS_PARTITION 1
+
+#include <asm/arch/pxa-regs.h> /* for OHCI_REGS_BASE */
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE OHCI_REGS_BASE
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "delta"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
#define CONFIG_BOOTDELAY -1
#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
#define CONFIG_CMDLINE_TAG
#define CONFIG_TIMESTAMP
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_HUSH_PARSER 1
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER 1
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CFG_LONGHELP /* undef to save memory */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT "$ " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
#else
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#endif
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_DEVICE_NULLDEV 1
-#define CFG_MEMTEST_START 0x80400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x80800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x80400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x80800000 /* 4 ... 8 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
-#define CFG_HZ 3250000 /* incrementer freq: 3.25 MHz */
+#define CONFIG_SYS_HZ 1000
/* Monahans Core Frequency */
-#define CFG_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */
-#define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */
+#define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */
+#define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-/* #define CFG_MMC_BASE 0xF0000000 */
+/* #define CONFIG_SYS_MMC_BASE 0xF0000000 */
/*
* Stack sizes
#define PHYS_SDRAM_4 0x83000000 /* SDRAM Bank #4 */
#define PHYS_SDRAM_4_SIZE 0x1000000 /* 64 MB */
-#define CFG_DRAM_BASE 0x80000000 /* at CS0 */
-#define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */
+#define CONFIG_SYS_DRAM_BASE 0x80000000 /* at CS0 */
+#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB Ram */
-#undef CFG_SKIP_DRAM_SCRUB
+#undef CONFIG_SYS_SKIP_DRAM_SCRUB
/*
* NAND Flash
*/
-#undef CFG_NAND_LEGACY
+#undef CONFIG_NAND_LEGACY
-#define CFG_NAND0_BASE 0x0 /* 0x43100040 */ /* 0x10000000 */
-#undef CFG_NAND1_BASE
+#define CONFIG_SYS_NAND0_BASE 0x0 /* 0x43100040 */ /* 0x10000000 */
+#undef CONFIG_SYS_NAND1_BASE
-#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
/* nand timeout values */
-#define CFG_NAND_PROG_ERASE_TO 3000
-#define CFG_NAND_OTHER_TO 100
-#define CFG_NAND_SENDCMD_RETRY 3
+#define CONFIG_SYS_NAND_PROG_ERASE_TO 3000
+#define CONFIG_SYS_NAND_OTHER_TO 100
+#define CONFIG_SYS_NAND_SENDCMD_RETRY 3
#undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */
/* NAND Timing Parameters (in ns) */
#define NAND_TIMING_tAR 10
/* NAND debugging */
-#define CFG_DFC_DEBUG1 /* usefull */
-#undef CFG_DFC_DEBUG2 /* noisy */
-#undef CFG_DFC_DEBUG3 /* extremly noisy */
+#define CONFIG_SYS_DFC_DEBUG1 /* usefull */
+#undef CONFIG_SYS_DFC_DEBUG2 /* noisy */
+#undef CONFIG_SYS_DFC_DEBUG3 /* extremly noisy */
#define CONFIG_MTD_DEBUG
#define CONFIG_MTD_DEBUG_VERBOSE 1
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NO_FLASH 1
+#define CONFIG_SYS_NO_FLASH 1
-#define CFG_ENV_IS_IN_NAND 1
-#define CFG_ENV_OFFSET 0x40000
-#define CFG_ENV_OFFSET_REDUND 0x44000
-#define CFG_ENV_SIZE 0x4000
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_OFFSET 0x40000
+#define CONFIG_ENV_OFFSET_REDUND 0x44000
+#define CONFIG_ENV_SIZE 0x4000
#endif /* __CONFIG_H */