#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* Define this to make U-Boot skip low level initialization when loaded
#define SONATA_BOARD
#define CONFIG_SYS_NAND_SMALLPAGE
#define CONFIG_SYS_USE_NOR
+#define CONFIG_DISPLAY_CPUINFO
/*===================*/
/* SoC Configuration */
/*===================*/
/* Memory Info */
/*=============*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */
#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
/* Network & Ethernet Configuration */
/*==================================*/
#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM 1
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_NET_MULTI
/*=====================*/
/* Flash & Environment */
/*=====================*/
#ifdef CONFIG_SYS_USE_NAND
#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS 2
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_OVERWRITE /* instead if obsoleted forceenv() */
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */
-#define CONFIG_ENV_SIZE SZ_16K
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#define CONFIG_SYS_NAND_BASE 0x02000000
#define CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#define DEF_BOOTM ""
#elif defined(CONFIG_SYS_USE_NOR)
#ifdef CONFIG_NOR_UART_BOOT
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
#else
#undef CONFIG_SKIP_LOWLEVEL_INIT
-#undef CONFIG_SKIP_RELOCATE_UBOOT
#endif
#define CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
#define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* 128KB sect size AMD Flash */
#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*2)
+#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
#define PHYS_FLASH_1 0x02000000 /* CS2 Base address */
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */
#define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */
#else
#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
#endif
-/*=======================*/
-/* KGDB support (if any) */
-/*=======================*/
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
-#endif
+
+#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */