#define CONFIG_CMD_FLASH
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_NET
-#define CONFIG_CMD_ENV
+#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_RUN
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_ECHO
* used for the RAM copy of the uboot code
*
*/
-#define CFG_MALLOC_LEN (128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "uboot> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 128 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 128 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_LOAD_ADDR 0xa3000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0xa3000000 /* default load address */
/* RS: where is this documented? */
/* RS: is this where U-Boot is */
/* RS: relocated to in RAM? */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_HZ 1000
/* RS: the oscillator is actually 3680130?? */
-#define CFG_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */
+#define CONFIG_SYS_CPUSPEED 0x141 /* set core clock to 200/200/100 MHz */
/* 0101000001 */
/* ^^^^^ Memory Speed 99.53 MHz */
/* ^^ Run Mode Speed = 2x Mem Speed */
/* ^^ Turbo Mode Sp. = 1x Run M. Sp. */
-#define CFG_MONITOR_LEN 0x20000 /* 128 KiB */
+#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128 KiB */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Network chip
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */
-#define CFG_DRAM_BASE 0xa0000000 /* RAM starts here */
-#define CFG_DRAM_SIZE 0x02000000
+#define CONFIG_SYS_DRAM_BASE 0xa0000000 /* RAM starts here */
+#define CONFIG_SYS_DRAM_SIZE 0x02000000
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
# if 0
/* FIXME: switch to _documented_ registers */
* GP79 == nCS3 is 1
* GP80 == nCS4 is 1
*/
-#define CFG_GPSR0_VAL 0x03008000
-#define CFG_GPSR1_VAL 0xC0028282
-#define CFG_GPSR2_VAL 0x0001C000
+#define CONFIG_SYS_GPSR0_VAL 0x03008000
+#define CONFIG_SYS_GPSR1_VAL 0xC0028282
+#define CONFIG_SYS_GPSR2_VAL 0x0001C000
/* GP02 == DON_RST is 0
* GP23 == SCLK is 0
* GP61 == LED_A is 0
* GP73 == SWUPD_LED is 0
*/
-#define CFG_GPCR0_VAL 0x00800004
-#define CFG_GPCR1_VAL 0x30002000
-#define CFG_GPCR2_VAL 0x00000100
+#define CONFIG_SYS_GPCR0_VAL 0x00800004
+#define CONFIG_SYS_GPCR1_VAL 0x30002000
+#define CONFIG_SYS_GPCR2_VAL 0x00000100
/* GP00 == DON_READY is input
* GP01 == DON_OK is input
* GP79 == nCS3 is output
* GP80 == nCS4 is output
*/
-#define CFG_GPDR0_VAL 0x03808004
-#define CFG_GPDR1_VAL 0xF002A282
-#define CFG_GPDR2_VAL 0x0001C200
+#define CONFIG_SYS_GPDR0_VAL 0x03808004
+#define CONFIG_SYS_GPDR1_VAL 0xF002A282
+#define CONFIG_SYS_GPDR2_VAL 0x0001C200
/* GP15 == nCS1 is AF10
* GP18 == RDY is AF01
* GP79 == nCS3 is AF10
* GP80 == nCS4 is AF10
*/
-#define CFG_GAFR0_L_VAL 0x80000000
-#define CFG_GAFR0_U_VAL 0x001A8010
-#define CFG_GAFR1_L_VAL 0x60088058
-#define CFG_GAFR1_U_VAL 0x00000008
-#define CFG_GAFR2_L_VAL 0xA0000000
-#define CFG_GAFR2_U_VAL 0x00000002
+#define CONFIG_SYS_GAFR0_L_VAL 0x80000000
+#define CONFIG_SYS_GAFR0_U_VAL 0x001A8010
+#define CONFIG_SYS_GAFR1_L_VAL 0x60088058
+#define CONFIG_SYS_GAFR1_U_VAL 0x00000008
+#define CONFIG_SYS_GAFR2_L_VAL 0xA0000000
+#define CONFIG_SYS_GAFR2_U_VAL 0x00000002
/* FIXME: set GPIO_RER/FER */
* BFS = 1
* SSS = 1
*/
-#define CFG_PSSR_VAL 0x37
+#define CONFIG_SYS_PSSR_VAL 0x37
/*
* Memory settings
* [03] 1 - 16 Bit bus width
* [02:00] 000 - nonburst RAM or FLASH
*/
-#define CFG_MSC0_VAL 0x25b825b8 /* flash banks */
+#define CONFIG_SYS_MSC0_VAL 0x25b825b8 /* flash banks */
/* This is the configuration for nCS2/3 -> TDM-Switch, DSP
* configuration for nCS3: DSP
* [03] 1 - 16 Bit bus width
* [02:00] 100 - variable latency I/O
*/
-#define CFG_MSC1_VAL 0x123C593C /* TDM switch, DSP */
+#define CONFIG_SYS_MSC1_VAL 0x123C593C /* TDM switch, DSP */
/* This is the configuration for nCS4/5 -> ExtBus, LAN Controller
*
* [03] 1 - 16 Bit bus width
* [02:00] 100 - variable latency I/O
*/
-#define CFG_MSC2_VAL 0x123C6CDC /* extra bus, LAN controller */
+#define CONFIG_SYS_MSC2_VAL 0x123C6CDC /* extra bus, LAN controller */
/* MDCNFG: SDRAM Configuration Register
*
* [00] 1 - enable SDRAM partition 0
*/
/* use the configuration above but disable partition 0 */
-#define CFG_MDCNFG_VAL 0x000019c8
+#define CONFIG_SYS_MDCNFG_VAL 0x000019c8
/* MDREFR: SDRAM Refresh Control Register
*
* [12] 1 - E0PIN: disable SDCKE0
* [11:00] 000000011000 - (64ms/8192)*MemClkFreq/32 = 24
*/
-#define CFG_MDREFR_VAL 0x0081D018
+#define CONFIG_SYS_MDREFR_VAL 0x0081D018
/* MDMRS: Mode Register Set Configuration Register
*
* [03] 0 - MDADD0: SDRAM0/1 burst Type. Fixed to sequential.
* [02:00] 010 - MDBL0: SDRAM0/1 burst Length. Fixed to 4.
*/
-#define CFG_MDMRS_VAL 0x00020022
+#define CONFIG_SYS_MDMRS_VAL 0x00020022
/*
* PCMCIA and CF Interfaces
*/
-#define CFG_MECR_VAL 0x00000000
-#define CFG_MCMEM0_VAL 0x00000000
-#define CFG_MCMEM1_VAL 0x00000000
-#define CFG_MCATT0_VAL 0x00000000
-#define CFG_MCATT1_VAL 0x00000000
-#define CFG_MCIO0_VAL 0x00000000
-#define CFG_MCIO1_VAL 0x00000000
+#define CONFIG_SYS_MECR_VAL 0x00000000
+#define CONFIG_SYS_MCMEM0_VAL 0x00000000
+#define CONFIG_SYS_MCMEM1_VAL 0x00000000
+#define CONFIG_SYS_MCATT0_VAL 0x00000000
+#define CONFIG_SYS_MCATT1_VAL 0x00000000
+#define CONFIG_SYS_MCIO0_VAL 0x00000000
+#define CONFIG_SYS_MCIO1_VAL 0x00000000
#endif
/*
* GPIO settings
*/
-#define CFG_GPSR0_VAL 0xFFFFFFFF
-#define CFG_GPSR1_VAL 0xFFFFFFFF
-#define CFG_GPSR2_VAL 0xFFFFFFFF
-#define CFG_GPCR0_VAL 0x08022080
-#define CFG_GPCR1_VAL 0x00000000
-#define CFG_GPCR2_VAL 0x00000000
-#define CFG_GPDR0_VAL 0xCD82A878
-#define CFG_GPDR1_VAL 0xFCFFAB80
-#define CFG_GPDR2_VAL 0x0001FFFF
-#define CFG_GAFR0_L_VAL 0x80000000
-#define CFG_GAFR0_U_VAL 0xA5254010
-#define CFG_GAFR1_L_VAL 0x599A9550
-#define CFG_GAFR1_U_VAL 0xAAA5AAAA
-#define CFG_GAFR2_L_VAL 0xAAAAAAAA
-#define CFG_GAFR2_U_VAL 0x00000002
+#define CONFIG_SYS_GPSR0_VAL 0xFFFFFFFF
+#define CONFIG_SYS_GPSR1_VAL 0xFFFFFFFF
+#define CONFIG_SYS_GPSR2_VAL 0xFFFFFFFF
+#define CONFIG_SYS_GPCR0_VAL 0x08022080
+#define CONFIG_SYS_GPCR1_VAL 0x00000000
+#define CONFIG_SYS_GPCR2_VAL 0x00000000
+#define CONFIG_SYS_GPDR0_VAL 0xCD82A878
+#define CONFIG_SYS_GPDR1_VAL 0xFCFFAB80
+#define CONFIG_SYS_GPDR2_VAL 0x0001FFFF
+#define CONFIG_SYS_GAFR0_L_VAL 0x80000000
+#define CONFIG_SYS_GAFR0_U_VAL 0xA5254010
+#define CONFIG_SYS_GAFR1_L_VAL 0x599A9550
+#define CONFIG_SYS_GAFR1_U_VAL 0xAAA5AAAA
+#define CONFIG_SYS_GAFR2_L_VAL 0xAAAAAAAA
+#define CONFIG_SYS_GAFR2_U_VAL 0x00000002
/* FIXME: set GPIO_RER/FER */
-#define CFG_PSSR_VAL 0x20
+#define CONFIG_SYS_PSSR_VAL 0x20
/*
* Memory settings
*/
-#define CFG_MSC0_VAL 0x2ef15af0
-#define CFG_MSC1_VAL 0x00003ff4
-#define CFG_MSC2_VAL 0x7ff07ff0
-#define CFG_MDCNFG_VAL 0x09a909a9
-#define CFG_MDREFR_VAL 0x038ff030
-#define CFG_MDMRS_VAL 0x00220022
+#define CONFIG_SYS_MSC0_VAL 0x2ef15af0
+#define CONFIG_SYS_MSC1_VAL 0x00003ff4
+#define CONFIG_SYS_MSC2_VAL 0x7ff07ff0
+#define CONFIG_SYS_MDCNFG_VAL 0x09a909a9
+#define CONFIG_SYS_MDREFR_VAL 0x038ff030
+#define CONFIG_SYS_MDMRS_VAL 0x00220022
/*
* PCMCIA and CF Interfaces
*/
-#define CFG_MECR_VAL 0x00000000
-#define CFG_MCMEM0_VAL 0x00000000
-#define CFG_MCMEM1_VAL 0x00000000
-#define CFG_MCATT0_VAL 0x00000000
-#define CFG_MCATT1_VAL 0x00000000
-#define CFG_MCIO0_VAL 0x00000000
-#define CFG_MCIO1_VAL 0x00000000
+#define CONFIG_SYS_MECR_VAL 0x00000000
+#define CONFIG_SYS_MCMEM0_VAL 0x00000000
+#define CONFIG_SYS_MCMEM1_VAL 0x00000000
+#define CONFIG_SYS_MCATT0_VAL 0x00000000
+#define CONFIG_SYS_MCATT1_VAL 0x00000000
+#define CONFIG_SYS_MCIO0_VAL 0x00000000
+#define CONFIG_SYS_MCIO1_VAL 0x00000000
#define CSB226_USER_LED0 0x00000008
#define CSB226_USER_LED1 0x00000010
/*
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sect. on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sect. on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000)
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x1C000)
/* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
#endif /* __CONFIG_H */