#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg
+#if defined(CONFIG_P3041DS)
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p3041ds.cfg
+#elif defined(CONFIG_P4080DS)
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p4080ds.cfg
+#elif defined(CONFIG_P5020DS)
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p5020ds.cfg
+#endif
#endif
-#ifdef CONFIG_SRIOBOOT_SLAVE
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
-#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
-#define CONFIG_SYS_SRIOBOOT_SLAVE_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIOBOOT_SLAVE_ADDR)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_NO_FLASH
#endif
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1 /* SRIO port 1 */
-#define CONFIG_SRIO2 /* SRIO port 2 */
-
#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIOBOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_ENV_IS_NOWHERE
#endif
#else
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIOBOOT_SLAVE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
#define CONFIG_ENV_IS_IN_REMOTE
#define CONFIG_ENV_ADDR 0xffe20000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_DDR_SPD
#define CONFIG_FSL_DDR3
-#ifdef CONFIG_P3060QDS
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#else
#define CONFIG_SYS_SPD_BUS_NUM 1
-#endif
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
/*
- * SRIOBOOT - SLAVE
+ * SRIO_PCIE_BOOT - SLAVE
*/
-#ifdef CONFIG_SRIOBOOT_SLAVE
-#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR_PHYS \
- (0x300000000ull | CONFIG_SYS_SRIOBOOT_UCODE_ENV_ADDR)
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif
/*
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIOBOOT_SLAVE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
* in two corenet boards, slave's ucode could be stored in master's memory
* space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO outbound window->master inbound window->master LAW->
- * the ucode address in master's NOR flash.
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
#define CONFIG_BAUDRATE 115200
-#if defined(CONFIG_P4080DS) || defined(CONFIG_P3060QDS)
+#ifdef CONFIG_P4080DS
#define __USB_PHY_TYPE ulpi
#else
#define __USB_PHY_TYPE utmi
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
"bank_intlv=cs0_cs1;" \
- "usb1:dr_mode=host,phy_type=" MK_STR(__USB_PHY_TYPE) "\0"\
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "ubootaddr=" MK_STR(CONFIG_SYS_TEXT_BASE) "\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
"tftpflash=tftpboot $loadaddr $uboot && " \
"protect off $ubootaddr +$filesize && " \
"erase $ubootaddr +$filesize && " \