mx6_common: Do not select esdhc DDR mode for all boards

[oweals/u-boot.git] / include / configs / cm_t35.h

diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 8c60e22c1dd053e5e98c1deff068b470c6066469..9feca1b47b381f6a40ba295c80a4102f2fc6127e 100644 (file)
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -21,11 +21,11 @@
  * High Level Configuration Options
  */
 #define CONFIG_OMAP    /* in a TI OMAP core */
-#define CONFIG_OMAP34XX        /* which is a 34XX */
 #define CONFIG_OMAP_GPIO
 #define CONFIG_CMD_GPIO
 #define CONFIG_CM_T3X  /* working with CM-T35 and CM-T3730 */
 #define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_GENERIC_BOARD
 
 #define CONFIG_SDRC    /* The chip has SDRC controller */
 
@@ -104,8 +104,6 @@
 #define CONFIG_USB_DEVICE
 #define CONFIG_USB_TTY
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
-/* This delay is really for slow-to-power-on USB sticks, not the hub */
-#define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 500
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -138,6 +136,7 @@
 #define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS      0
 #define CONFIG_I2C_MULTI_BUS
 
 /*
@@ -260,9 +259,6 @@
  */
 
 /* **** PISMO SUPPORT *** */
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE               GPMC_SIZE_128M
-
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 2 sectors */
@@ -314,6 +310,7 @@
 
 #define CONFIG_LCD
 #define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SOURCE
 #define CONFIG_CMD_BMP
 #define CONFIG_BMP_16BPP
 #define CONFIG_SCF0403_LCD
@@ -321,14 +318,13 @@
 #define CONFIG_OMAP3_SPI
 
 /* Defines for SPL */
-#define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE
 
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR        0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION   1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME       "u-boot.img"
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -369,7 +365,6 @@
 
 #define CONFIG_SPL_TEXT_BASE           0x40200800
 #define CONFIG_SPL_MAX_SIZE            (54 * 1024)     /* 8 KB for stack */
-#define CONFIG_SPL_STACK               LOW_LEVEL_SRAM_STACK
 
 /*
  * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the