/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
-#define CONFIG_CANYONLANDS 1 /* Board is Canyonlands */
+/*
+ * This config file is used for Canyonlands (460EX) Glacier (460GT)
+ * and Arches dual (460GT)
+ */
+#ifdef CONFIG_CANYONLANDS
+#define CONFIG_460EX 1 /* Specific PPC460EX */
+#define CONFIG_HOSTNAME canyonlands
+#else
+#define CONFIG_460GT 1 /* Specific PPC460GT */
+#ifdef CONFIG_GLACIER
+#define CONFIG_HOSTNAME glacier
+#else
+#define CONFIG_HOSTNAME arches
+#define CONFIG_USE_NETDEV eth1
+#define CONFIG_BD_NUM_CPUS 2
+#endif
+#endif
+
#define CONFIG_440 1
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_460EX 1 /* Specific PPC460EX support */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_TYPES 1 /* support board types */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
+#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
-#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
+#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
+#define CONFIG_SYS_PCIE_BASE 0xc4000000 /* PCIe UTL regs */
-#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
-#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
-#define CFG_PCIE_BASE 0xc4000000 /* PCIe UTL regs */
+#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
+#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
+#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
+#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
-#define CFG_PCIE0_CFGBASE 0xc0000000
-#define CFG_PCIE1_CFGBASE 0xc1000000
-#define CFG_PCIE0_XCFGBASE 0xc3000000
-#define CFG_PCIE1_XCFGBASE 0xc3001000
+/*
+ * BCSR bits as defined in the Canyonlands board user manual.
+ */
+#define BCSR_USBCTRL_OTG_RST 0x32
+#define BCSR_USBCTRL_HOST_RST 0x01
+#define BCSR_SELECT_PCIE 0x10
-#define CFG_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */
+#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */
/* base address of inbound PCIe window */
-#define CFG_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */
+#define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */
/* EBC stuff */
-#define CFG_NAND_ADDR 0xE0000000
-#define CFG_BCSR_BASE 0xE1000000
-#define CFG_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */
-#define CFG_FLASH_BASE 0xFC000000 /* later mapped to this addr */
-#define CFG_FLASH_BASE_PHYS_H 0x4
-#define CFG_FLASH_BASE_PHYS_L 0xCC000000
-#define CFG_FLASH_BASE_PHYS (((u64)CFG_FLASH_BASE_PHYS_H << 32) | \
- (u64)CFG_FLASH_BASE_PHYS_L)
-#define CFG_FLASH_SIZE (64 << 20)
-
-#define CFG_OCM_BASE 0xE3000000 /* OCM: 16k */
-#define CFG_SRAM_BASE 0xE8000000 /* SRAM: 256k */
-#define CFG_LOCAL_CONF_REGS 0xEF000000
-
-#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals */
-
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/
+#if !defined(CONFIG_ARCHES)
+#define CONFIG_SYS_BCSR_BASE 0xE1000000
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped to this addr */
+#define CONFIG_SYS_FLASH_SIZE (64 << 20)
+#else
+#define CONFIG_SYS_FPGA_BASE 0xE1000000
+#define CONFIG_SYS_CPLD_ADDR (CONFIG_SYS_FPGA_BASE + 0x00080000)
+#define CONFIG_SYS_CPLD_DATA (CONFIG_SYS_FPGA_BASE + 0x00080002)
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* later mapped to this addr */
+#define CONFIG_SYS_FLASH_SIZE (32 << 20)
+#endif
+
+#define CONFIG_SYS_NAND_ADDR 0xE0000000
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */
+#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4
+#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000
+#define CONFIG_SYS_FLASH_BASE_PHYS (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) | \
+ (u64)CONFIG_SYS_FLASH_BASE_PHYS_L)
+
+#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */
+#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */
+#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000
+
+#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals */
+
+#define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals */
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in OCM)
*----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
* Define here the location of the environment variables (FLASH).
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_SYS_NOR_CS 3 /* NOR chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*
* On 440EPx the SPL is copied to SDRAM before the NAND controller is
* set up. While still running from cache, I experienced problems accessing
* the NAND controller. sr - 2006-08-25
+ *
+ * This is the first official implementation of booting from 2k page sized
+ * NAND devices (e.g. Micron 29F2G08AA 256Mbit * 8)
*/
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from */
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */
/* this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (1 << 20) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
-
-#define CFG_NAND_ECCSIZE 256
-#define CFG_NAND_ECCBYTES 3
-#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
-#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
-
-#ifdef CFG_ENV_IS_IN_NAND
+#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE)
+ /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 /* Location of bad block marker*/
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE /* Fifth addr used (<=128MB) */
+
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63}
+
+#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* NAND-FLASH related
*----------------------------------------------------------------------*/
-#define CFG_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*------------------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT)
+#if !defined(CONFIG_ARCHES)
/*
* NAND booting U-Boot version uses a fixed initialization, since the whole
* I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot
#define SPD_EEPROM_ADDRESS {0x50, 0x51} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC 1 /* with ECC support */
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */
-#endif
-#define CFG_MBYTES_SDRAM 256 /* 256MB */
+
+#else /* defined(CONFIG_ARCHES) */
+
+#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */
+
+#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */
+#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
+#undef CONFIG_PPC4xx_DDR_METHOD_A
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+/* Memory Queue */
+#define CONFIG_SYS_SDRAM_R0BAS 0x0000f000
+#define CONFIG_SYS_SDRAM_R1BAS 0x00000000
+#define CONFIG_SYS_SDRAM_R2BAS 0x00000000
+#define CONFIG_SYS_SDRAM_R3BAS 0x00000000
+#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000
+#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008
+#define CONFIG_SYS_SDRAM_CONF1LL 0x00001080
+#define CONFIG_SYS_SDRAM_CONF1HB 0x00001080
+#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000
+
+/* SDRAM Controller */
+#define CONFIG_SYS_SDRAM0_MB0CF 0x00000701
+#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000
+#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000
+#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000
+#define CONFIG_SYS_SDRAM0_MCOPT1 0x05322000
+#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
+#define CONFIG_SYS_SDRAM0_MODT0 0x01000000
+#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
+#define CONFIG_SYS_SDRAM0_MODT2 0x00000000
+#define CONFIG_SYS_SDRAM0_MODT3 0x00000000
+#define CONFIG_SYS_SDRAM0_CODT 0x00800021
+#define CONFIG_SYS_SDRAM0_RTR 0x06180000
+#define CONFIG_SYS_SDRAM0_INITPLR0 0xb5380000
+#define CONFIG_SYS_SDRAM0_INITPLR1 0x82100400
+#define CONFIG_SYS_SDRAM0_INITPLR2 0x80820000
+#define CONFIG_SYS_SDRAM0_INITPLR3 0x80830000
+#define CONFIG_SYS_SDRAM0_INITPLR4 0x80810040
+#define CONFIG_SYS_SDRAM0_INITPLR5 0x80800532
+#define CONFIG_SYS_SDRAM0_INITPLR6 0x82100400
+#define CONFIG_SYS_SDRAM0_INITPLR7 0x8a080000
+#define CONFIG_SYS_SDRAM0_INITPLR8 0x8a080000
+#define CONFIG_SYS_SDRAM0_INITPLR9 0x8a080000
+#define CONFIG_SYS_SDRAM0_INITPLR10 0x8a080000
+#define CONFIG_SYS_SDRAM0_INITPLR11 0x80000432
+#define CONFIG_SYS_SDRAM0_INITPLR12 0x808103c0
+#define CONFIG_SYS_SDRAM0_INITPLR13 0x80810040
+#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000
+#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000
+#define CONFIG_SYS_SDRAM0_RQDC 0x80000038
+#define CONFIG_SYS_SDRAM0_RFDC 0x00000257
+#define CONFIG_SYS_SDRAM0_RDCC 0x40000000
+#define CONFIG_SYS_SDRAM0_DLCR 0x03000091
+#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000
+#define CONFIG_SYS_SDRAM0_WRDTR 0x82000823
+#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000
+#define CONFIG_SYS_SDRAM0_SDTR2 0x42204243
+#define CONFIG_SYS_SDRAM0_SDTR3 0x090c0d1a
+#define CONFIG_SYS_SDRAM0_MMODE 0x00000432
+#define CONFIG_SYS_SDRAM0_MEMODE 0x00000004
+#endif /* !defined(CONFIG_ARCHES) */
+#endif /* !defined(CONFIG_NAND_U_BOOT) */
+
+#define CONFIG_SYS_MBYTES_SDRAM 512 /* 512MB */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
+
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C bootstrap EEPROM */
+#if defined(CONFIG_ARCHES)
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54
+#else
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
+#endif
+#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
+#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#if defined(CONFIG_ARCHES)
+#define CONFIG_SYS_I2C_DTT_ADDR 0x4a /* AD7414 I2C address */
+#endif
+
+#if !defined(CONFIG_ARCHES)
/* RTC configuration */
#define CONFIG_RTC_M41T62 1
-#define CFG_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#endif
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
+
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+
+#if !defined(CONFIG_ARCHES)
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
-#define CONFIG_HAS_ETH0 1
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_NET_MULTI 1
+/* Only Glacier (460GT) has 4 EMAC interfaces */
+#ifdef CONFIG_460GT
+#define CONFIG_PHY2_ADDR 2
+#define CONFIG_PHY3_ADDR 3
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#endif
+
+#else /* defined(CONFIG_ARCHES) */
+
+#define CONFIG_FIXED_PHY 0xFFFFFFFF
+#define CONFIG_PHY_ADDR CONFIG_FIXED_PHY
+#define CONFIG_PHY1_ADDR 0
+#define CONFIG_PHY2_ADDR 1
+#define CONFIG_HAS_ETH2
+
+#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
+ {devnum, speed, duplex}
+#define CONFIG_SYS_FIXED_PHY_PORTS \
+ CONFIG_SYS_FIXED_PHY_PORT(0, 1000, FULL)
+
+#define CONFIG_M88E1112_PHY
+
+/*
+ * For the GPCS_PHYx_ADDR PHY address, choose some PHY address not
+ * used by CONFIG_PHYx_ADDR
+ */
+#define CONFIG_GPCS_PHY_ADDR 0xA
+#define CONFIG_GPCS_PHY1_ADDR 0xB
+#define CONFIG_GPCS_PHY2_ADDR 0xC
+#endif /* !defined(CONFIG_ARCHES) */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=canyonlands\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty;" \
- "bootm 200000\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty;" \
- "bootm 200000 - ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "rootpath=/opt/eldk/ppc_4xxFP\0" \
- "bootfile=canyonlands/uImage\0" \
- "fdt_file=canyonlands/canyonlands.dtb\0" \
- "fdt_addr=400000\0" \
+/*-----------------------------------------------------------------------
+ * USB-OHCI
+ *----------------------------------------------------------------------*/
+/* Only Canyonlands (460EX) has USB */
+#ifdef CONFIG_460EX
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors */
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */
+#define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */
+#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000)
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
+#endif
+
+/*
+ * Default environment variables
+ */
+#if !defined(CONFIG_ARCHES)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fc000000\0" \
+ "fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 canyonlands/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 canyonlands/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
+#else /* defined(CONFIG_ARCHES) */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ "kernel_addr=fe000000\0" \
+ "fdt_addr=fe1e0000\0" \
+ "ramdisk_addr=fe200000\0" \
+ "pciconfighost=1\0" \
+ "pcie_mode=RP:RP\0" \
+ "ethprime=ppc_4xx_eth1\0" \
+ ""
+#endif /* !defined(CONFIG_ARCHES) */
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CHIP_CONFIG
+#if defined(CONFIG_ARCHES)
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SDRAM
+#elif defined(CONFIG_CANYONLANDS)
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SATA
#define CONFIG_CMD_SDRAM
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+#elif defined(CONFIG_GLACIER)
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#error "board type not defined"
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT /* let board init pci target */
-#undef CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
+#undef CONFIG_SYS_PCI_MASTER_INIT
-#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#ifdef CONFIG_460GT
+#if defined(CONFIG_ARCHES)
+/*-----------------------------------------------------------------------
+ * RapidIO I/O and Registers
+ *----------------------------------------------------------------------*/
+#define CONFIG_RAPIDIO
+#define CONFIG_SYS_460GT_SRIO_ERRATA_1
+
+#define SRGPL0_REG_BAR 0x0000000DAA000000ull /* 16MB */
+#define SRGPL0_CFG_BAR 0x0000000DAB000000ull /* 16MB */
+#define SRGPL0_MNT_BAR 0x0000000DAC000000ull /* 16MB */
+#define SRGPL0_MSG_BAR 0x0000000DAD000000ull /* 16MB */
+#define SRGPL0_OUT_BAR 0x0000000DB0000000ull /* 256MB */
+
+#define CONFIG_SYS_SRGPL0_REG_BAR 0xAA000000 /* 16MB */
+#define CONFIG_SYS_SRGPL0_CFG_BAR 0xAB000000 /* 16MB */
+#define CONFIG_SYS_SRGPL0_MNT_BAR 0xAC000000 /* 16MB */
+#define CONFIG_SYS_SRGPL0_MSG_BAR 0xAD000000 /* 16MB */
+
+#define CONFIG_SYS_I2ODMA_BASE 0xCF000000
+#define CONFIG_SYS_I2ODMA_PHYS_ADDR 0x0000000400100000ull
+
+#define CONFIG_PPC4XX_RAPIDIO_PROMISCUOUS_MODE
+#undef CONFIG_PPC4XX_RAPIDIO_DEBUG
+#undef CONFIG_PPC4XX_RAPIDIO_IN_BAR_USE_OCM
+#define CONFIG_PPC4XX_RAPIDIO_USE_HB_PLB
+#undef CONFIG_PPC4XX_RAPIDIO_LOOPBACK
+#endif /* CONFIG_ARCHES */
+#endif /* CONFIG_460GT */
/*
- * Internal Definitions
+ * SATA driver setup
*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_SATA_DWC
+#define CONFIG_LIBATA
+#define SATA_BASE_ADDR 0xe20d1000 /* PPC460EX SATA Base Address */
+#define SATA_DMA_REG_ADDR 0xe20d0800 /* PPC460EX SATA Base Address */
+#define CONFIG_SYS_SATA_MAX_DEVICE 1 /* SATA MAX DEVICE */
+/* Convert sectorsize to wordsize */
+#define ATA_SECTOR_WORDS (ATA_SECT_SIZE/2)
#endif
/*-----------------------------------------------------------------------
* EBC address which accepts bigger regions:
*
* 0xfc00.0000 -> 4.cc00.0000
+ *
+ * Arches has 32MBytes of NOR FLASH (Spansion 29GL256), it will be
+ * remapped to:
+ *
+ * 0xfe00.0000 -> 4.ce00.0000
*/
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
/* Memory Bank 3 (NOR-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x10055e00
-#define CFG_EBC_PB3CR (CFG_BOOT_BASE_ADDR | 0x9a000)
+#define CONFIG_SYS_EBC_PB3AP 0x10055e00
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)
/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
#else
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x10055e00
-#define CFG_EBC_PB0CR (CFG_BOOT_BASE_ADDR | 0x9a000)
+#define CONFIG_SYS_EBC_PB0AP 0x10055e00
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)
+#if !defined(CONFIG_ARCHES)
/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
+#define CONFIG_SYS_EBC_PB3AP 0x018003c0
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
#endif
+#endif /*defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */
+#if !defined(CONFIG_ARCHES)
/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x00804240
-#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */
+#define CONFIG_SYS_EBC_PB2AP 0x00804240
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */
-#define CFG_EBC_CFG 0xB8400000 /* EBC0_CFG */
+#else /* defined(CONFIG_ARCHES) */
+
+/* Memory Bank 1 (FPGA) initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x7f8ffe80
+#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/
+#endif /* !defined(CONFIG_ARCHES) */
+
+#define CONFIG_SYS_EBC_CFG 0xbfc00000
+
+/*
+ * Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO
+ * pin multiplexing correctly
+ */
+#if defined(CONFIG_ARCHES)
+#define GPIO43_USE GPIO_SEL /* On Arches this pin is used as GPIO */
+#else
+#define GPIO43_USE GPIO_ALT1 /* On Glacier this pin is used as ALT1 -> PerCS3 */
+#endif
/*
* PPC4xx GPIO Configuration
*/
-#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+#ifdef CONFIG_460EX
+/* 460EX: Use USB configuration */
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
-{GPIO0_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
-{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
-{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
-{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
-{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
-{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
+#else
+/* 460GT: Use EMAC2+3 configuration */
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
+{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
+}, \
+{ \
+/* GPIO Core 1 */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
+{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
+{GPIO1_BASE, GPIO_OUT, GPIO43_USE, GPIO_OUT_0},/* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
+{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
+{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
+} \
+}
+#endif
#endif /* __CONFIG_H */