* U-boot - Configuration file for BF537 STAMP board
*/
-#ifndef __CONFIG_BF537_H__
-#define __CONFIG_BF537_H__
+#ifndef __CONFIG_BF537_STAMP_H__
+#define __CONFIG_BF537_STAMP_H__
-#include <asm/blackfin-config-pre.h>
+#include <asm/config-pre.h>
-#define CFG_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_BAUDRATE 57600
-/* Set default serial console for bf537 */
-#define CONFIG_UART_CONSOLE 0
-#define CONFIG_BOOTDELAY 5
-/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
-/*#define CONFIG_BF537_STAMP_LEDCMD 1*/
-
-#define CONFIG_PANIC_HANG 1
-
-#define CONFIG_BFIN_CPU bf537-0.2
-#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-#define CONFIG_BFIN_MAC
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf537-0.2
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-/* This sets the default state of the cache on U-Boot's boot */
-#define CONFIG_ICACHE_ON
-#define CONFIG_DCACHE_ON
-/* Define if want to do post memory test */
-#undef CONFIG_POST_TEST
-
-#define CONFIG_RTC_BFIN 1
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-
-/* CONFIG_CLKIN_HZ is any value in Hz */
-#define CONFIG_CLKIN_HZ 25000000
-/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
-/* 1=CLKIN/2 */
-#define CONFIG_CLKIN_HALF 0
-/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
-/* 1=bypass PLL*/
-#define CONFIG_PLL_BYPASS 0
-/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
-/* Values can range from 1-64 */
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 20
-/* CONFIG_CCLK_DIV controls what the core clock divider is */
-/* Values can be 1, 2, 4, or 8 ONLY */
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
-/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
-/* Values can range from 1-15 */
-#define CONFIG_SCLK_DIV 5
-/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
-/* Values can range from 2-65535 */
-/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
-#define CONFIG_SPI_BAUD 2
-#define CONFIG_SPI_BAUD_INITBLOCK 4
-
-#if ( CONFIG_CLKIN_HALF == 0 )
-#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
-#else
-#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
-#endif
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 4
-#if (CONFIG_PLL_BYPASS == 0)
-#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
-#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
-#else
-#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
-#endif
-
-#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
-#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
-#define CONFIG_MEM_MT48LC32M8A2_75 1
-
-#define CONFIG_LOADS_ECHO 1
/*
- * rarpb, bootp or dhcp commands will perform only a
- * configuration lookup from the BOOTP/DHCP server
- * but not try to load any image using TFTP
+ * Memory Settings
*/
-#define CFG_AUTOLOAD "no"
+#define CONFIG_MEM_ADD_WDTH 10
+#define CONFIG_MEM_SIZE 64
+
+#define CONFIG_EBIU_SDRRC_VAL 0x306
+#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
+
/*
* Network Settings
*/
-/* network support */
-#ifdef CONFIG_BFIN_MAC
-#define CONFIG_IPADDR 192.168.0.15
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.2
-#define CONFIG_HOSTNAME BF537
+#ifndef __ADSPBF534__
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_BFIN_MAC
+#define CONFIG_NETCONSOLE 1
+#define CONFIG_NET_MULTI 1
#endif
-
-#define CONFIG_ROOTPATH /romfs
+#define CONFIG_HOSTNAME bf537-stamp
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
-
-#define CFG_LONGHELP 1
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#define CONFIG_BOOTCOMMAND "run ramboot"
-
-#if defined(CONFIG_POST_TEST)
-/* POST support */
-#define CONFIG_POST ( CFG_POST_MEMORY | \
- CFG_POST_UART | \
- CFG_POST_FLASH | \
- CFG_POST_ETHER | \
- CFG_POST_LED | \
- CFG_POST_BUTTON)
-#else
-#undef CONFIG_POST
-#endif
-
-#ifdef CONFIG_POST
-#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
-#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
-#endif
-
-/* CF-CARD IDE-HDD Support */
-/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
-/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
-/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
-
-#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
-# define CONFIG_BFIN_IDE 1
-#endif
-
-/*#define CONFIG_BF537_NAND */ /* Add nand flash support */
-
-#define CONFIG_NETCONSOLE 1
-#define CONFIG_NET_MULTI 1
/*
- * BOOTP options
+ * Flash Settings
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
+#define CONFIG_SYS_MAX_FLASH_SECT 71
/*
- * Command line configuration.
+ * SPI Settings
*/
-#include <config_cmd_default.h>
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+#define CONFIG_SF_DEFAULT_SPEED 30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ALL
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-#ifndef CONFIG_BFIN_MAC
-#undef CONFIG_CMD_NET
+/*
+ * Env Storage Settings
+ */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000
#else
-#define CONFIG_CMD_PING
-#endif
-
-#if defined(CONFIG_BFIN_CF_IDE) \
- || defined(CONFIG_BFIN_HDD_IDE) \
- || defined(CONFIG_BFIN_TRUE_IDE)
-#define CONFIG_CMD_IDE
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
-
-#define CONFIG_CMD_DHCP
-
-#if defined(CONFIG_POST)
-#define CONFIG_CMD_DIAG
-#endif
-
-#ifdef CONFIG_BF537_NAND
-#define CONFIG_CMD_NAND
-#endif
-
-
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-#define CONFIG_LOADADDR 0x1000000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux;" \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux;" \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.bin;" \
- "protect off 0x20000000 0x2007FFFF;" \
- "erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \
- ""
-
-#define CFG_PROMPT "bfin> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#endif
-#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024)
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0 /* memtest works on */
-#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
-#define CFG_LOAD_ADDR CONFIG_LOADADDR /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_SDRAM_BASE 0x00000000
-
-#define CFG_FLASH_BASE 0x20000000
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_PROTECTION
-#define CFG_MAX_FLASH_BANKS 1
-#define CFG_MAX_FLASH_SECT 71 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE 0x4000
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-
-#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0x4000
-#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
-#else
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20004000
-#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#ifdef ENV_IS_EMBEDDED
+/* WARNING - the following is hand-optimized to fit within
+ * the sector before the environment sector. If it throws
+ * an error during compilation remove an object here to get
+ * it linked after the configuration sector.
+ */
+# define LDS_BOARD_TEXT \
+ arch/blackfin/lib/libblackfin.o (.text*); \
+ arch/blackfin/cpu/libblackfin.o (.text*); \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text*);
#endif
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
-#define ENV_IS_EMBEDDED
-
-/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 15
-#define CONFIG_SPI
/*
- * Stack sizes
+ * I2C Settings
*/
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+#define CONFIG_BFIN_TWI_I2C 1
+#define CONFIG_HARD_I2C 1
-#define POLL_MODE 1
-#define FLASH_TOT_SECT 71
-#define FLASH_SIZE 0x400000
-#define CFG_FLASH_SIZE 0x400000
/*
- * Board NAND Infomation
+ * SPI_MMC Settings
*/
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC_SPI
-#define CFG_NAND_ADDR 0x20212000
-#define CFG_NAND_BASE CFG_NAND_ADDR
-#define CFG_MAX_NAND_DEVICE 1
-#define SECTORSIZE 512
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-#define BFIN_NAND_READY PF3
-
-#define NAND_WAIT_READY(nand) \
- do { \
- int timeout = 0; \
- while(!(*pPORTFIO & PF3)) \
- if (timeout++ > 100000) \
- break; \
+
+/*
+ * NAND Settings
+ */
+/* #define CONFIG_NAND_PLAT */
+#define CONFIG_SYS_NAND_BASE 0x20212000
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2))
+#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1))
+#define BFIN_NAND_WRITE(addr, cmd) \
+ do { \
+ bfin_write8(addr, cmd); \
+ SSYNC(); \
} while (0)
-#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */
-#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */
+#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
+#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
+#define NAND_PLAT_GPIO_DEV_READY GPIO_PF3
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
/*
- * Initialize PSD4256 registers for using I2C
+ * CF-CARD IDE-HDD Support
*/
-#define CONFIG_MISC_INIT_R
-
-#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
/*
- * I2C settings
- * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
+ * Add CF flash card support in TRUE-IDE Mode (CF-IDE-NAND Card)
+ * Strange address mapping Blackfin A13 connects to CF_A0
*/
-/* #define CONFIG_SOFT_I2C 1*/ /* I2C bit-banged */
-#define CONFIG_HARD_I2C 1 /* I2C TWI */
-#if defined CONFIG_HARD_I2C
-#define CONFIG_TWICLK_KHZ 50
-#endif
-#define CONFIG_EBIU_SDRRC_VAL 0x306
-#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
-#define CONFIG_EBIU_SDBCTL_VAL 0x25
+/* #define CONFIG_BFIN_TRUE_IDE */
-#define CONFIG_EBIU_AMGCTL_VAL 0xFF
-#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
-#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-
-#if defined CONFIG_SOFT_I2C
/*
- * Software (bit-bang) I2C driver configuration
+ * Add CF flash card support in Common Memory Mode (CF-IDE-NAND Card)
+ * This should be the preferred mode
*/
-#define PF_SCL PF0
-#define PF_SDA PF1
-
-#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
-#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
-#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
-#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
-#define I2C_SDA(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SDA; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SDA; \
- asm("ssync;"); \
- }
-#define I2C_SCL(bit) if(bit) { \
- *pFIO_FLAG_S = PF_SCL; \
- asm("ssync;"); \
- } \
- else { \
- *pFIO_FLAG_C = PF_SCL; \
- asm("ssync;"); \
- }
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#endif
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
+/* #define CONFIG_BFIN_CF_IDE */
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
+/*
+ * Add IDE Disk Drive (HDD) support
+ * See example interface here:
+ * http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:ide-blackfin
+ */
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
+/* #define CONFIG_BFIN_HDD_IDE */
+
+#if defined(CONFIG_BFIN_CF_IDE) || \
+ defined(CONFIG_BFIN_HDD_IDE) || \
+ defined(CONFIG_BFIN_TRUE_IDE)
+# define CONFIG_BFIN_IDE 1
+# define CONFIG_CMD_IDE
+#endif
#if defined(CONFIG_BFIN_IDE)
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
-#undef AMBCTL1VAL
-#define AMBCTL1VAL 0xFFC3FFC3
+#undef CONFIG_EBIU_AMBCTL1_VAL
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3
#define CONFIG_CF_ATASEL_DIS 0x20311800
#define CONFIG_CF_ATASEL_ENA 0x20311802
* Note that these settings aren't for the most part used in include/ata.h
* when all of the ATA registers are setup
*/
-#define CFG_ATA_BASE_ADDR 0x2031C000
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
-#define CFG_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */
-#endif /* CONFIG_BFIN_TRUE_IDE */
-
-#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */
-#define CFG_ATA_BASE_ADDR 0x20211800
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */
-#define CFG_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */
-#endif /* CONFIG_BFIN_CF_IDE */
-
-#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */
-#define CFG_ATA_BASE_ADDR 0x20314000
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
-#define CFG_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
-
+#define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
+#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A13 */
+
+#elif defined(CONFIG_BFIN_CF_IDE)
+#define CONFIG_SYS_ATA_BASE_ADDR 0x20211800
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */
+#define CONFIG_SYS_ATA_STRIDE 1 /* CF_A0=0, with /CE1 /CE2 odd/even byte selects */
+
+#elif defined(CONFIG_BFIN_HDD_IDE)
+#define CONFIG_SYS_ATA_BASE_ADDR 0x20314000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
+#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
+#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
#undef CONFIG_SCLK_DIV
#define CONFIG_SCLK_DIV 8
-#endif /* CONFIG_BFIN_HDD_IDE */
+#endif
+
+#endif
+
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST
+#ifdef CONFIG_POST
+#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
+#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
+#endif
+#define CONFIG_SYS_POST_WORD_ADDR 0xFF903FFC
+
+/* These are for board tests */
+#if 0
+#define CONFIG_BOOTCOMMAND "bootldr 0x203f0100"
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT \
+ "autoboot in %d seconds: press space to stop\n", bootdelay
+#define CONFIG_AUTOBOOT_STOP_STR " "
+#endif
-#endif /*CONFIG_BFIN_IDE */
-#include <asm/blackfin-config-post.h>
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
#endif