include/configs: Use new CONFIG_CMD_* in various c* named board config files.

[oweals/u-boot.git] / include / configs / bamboo.h

diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index cd5844363f88ce075e6cb72f7e60aea96f1b593e..c1fdaf8d5702e7adbd5edf50e82168de93bd4142 100644 (file)
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -316,45 +316,46 @@
 #define USB_2_0_DEVICE
 #endif /*CONFIG_440EP*/
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_SNTP
+
 #ifdef CONFIG_BAMBOO_NAND
-#define _CFG_CMD_NAND CFG_CMD_NAND
-#else
-#define _CFG_CMD_NAND 0
-#endif /* CONFIG_BAMBOO_NAND */
+#define CONFIG_CMD_NAND
+#endif
 
-#define CONFIG_COMMANDS               (CONFIG_CMD_DFL  | \
-                               CFG_CMD_ASKENV  | \
-                               CFG_CMD_DATE    | \
-                               CFG_CMD_DHCP    | \
-                               CFG_CMD_DIAG    | \
-                               CFG_CMD_ELF     | \
-                               CFG_CMD_EEPROM  | \
-                               CFG_CMD_I2C     | \
-                               CFG_CMD_IRQ     | \
-                               CFG_CMD_MII     | \
-                               CFG_CMD_NET     | \
-                               CFG_CMD_NFS     | \
-                               CFG_CMD_PCI     | \
-                               CFG_CMD_PING    | \
-                               CFG_CMD_REGINFO | \
-                               CFG_CMD_SDRAM   | \
-                               CFG_CMD_USB     | \
-                               CFG_CMD_FAT     | \
-                               CFG_CMD_EXT2    | \
-                               _CFG_CMD_NAND   | \
-                               CFG_CMD_SNTP    )
 
 #define CONFIG_SUPPORT_VFAT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP                   /* undef to save memory         */
 #define CFG_PROMPT             "=> "   /* Monitor Command Prompt       */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE             1024    /* Console I/O Buffer Size      */
 #else
 #define CFG_CBSIZE             256     /* Console I/O Buffer Size      */
@@ -389,7 +390,6 @@
 #define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
 
 /* Board-specific PCI */
-#define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
 #define CFG_PCI_TARGET_INIT
 #define CFG_PCI_MASTER_INIT
 
@@ -408,7 +408,7 @@
  */
 #define CFG_DCACHE_SIZE                (32<<10) /* For AMCC 440 CPUs                   */
 #define CFG_CACHELINE_SIZE     32      /* ...                  */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT    5       /* log base 2 of the above value        */
 #endif
 
@@ -420,7 +420,7 @@
 #define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
 #define BOOTFLAG_WARM  0x02            /* Software reboot                      */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif