#define CONFIG_ATC 1 /* ...on a ATC board */
#define CONFIG_CPM2 1 /* Has a CPM2 */
+#define CONFIG_SYS_TEXT_BASE 0xFF000000
+
/*
* select serial console configuration
*
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#define CONFIG_ETHER_ON_FCC
-#define CONFIG_NET_MULTI
#define CONFIG_ETHER_ON_FCC2
/*
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CONFIG_SYS_CPMFCR_RAMTYPE 0
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#define CONFIG_ETHER_ON_FCC3
* - RAM for BD/Buffers is on the local Bus (see 28-13)
* - Enable Half Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#define CONFIG_8260_CLKIN 64000000 /* in Hz */
#define CONFIG_BOOTCOMMAND \
"bootp;" \
"setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath} " \
+ "nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"\
"bootm"
*/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
/*
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_RESET_ADDRESS 0xFFF00100 /* "bad" address */
+#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */
-#define CFG_ALLOC_DPRAM
+#define CONFIG_SYS_ALLOC_DPRAM
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_RTC_DS12887
-#define RTC_BASE_ADDR 0xF5000000
-#define RTC_PORT_ADDR RTC_BASE_ADDR + 0x800
-#define RTC_PORT_DATA RTC_BASE_ADDR + 0x808
+#define RTC_BASE_ADDR 0xF5000000
+#define RTC_PORT_ADDR RTC_BASE_ADDR + 0x800
+#define RTC_PORT_DATA RTC_BASE_ADDR + 0x808
#define CONFIG_MISC_INIT_R
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* Flash configuration
*/
-#define CFG_FLASH_BASE 0xFF000000
-#define CFG_FLASH_SIZE 0x00800000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 0x00800000
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CONFIG_FLASH_16BIT
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*
- * if you change bits in the HRCW, you must also change the CFG_*
+ * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
* defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
*/
-#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
+#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
HRCW_BPS10 |\
HRCW_APPC10)
/* no slaves so just fill with zeros */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xF0000000
+#define CONFIG_SYS_IMMR 0xF0000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*
- * 60x SDRAM is mapped at CFG_SDRAM_BASE.
+ * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE.
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_PCI
#define CONFIG_PCI_PNP
-#define CFG_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
+#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
#if 1
/* environment is in Flash */
-#define CFG_ENV_IS_IN_FLASH 1
-# define CFG_ENV_ADDR (CFG_FLASH_BASE+0x30000)
-# define CFG_ENV_SIZE 0x10000
-# define CFG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_IS_IN_FLASH 1
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x30000)
+# define CONFIG_ENV_SIZE 0x10000
+# define CONFIG_ENV_SECT_SIZE 0x10000
#else
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0
-#define CFG_ENV_SIZE 2048
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_OFFSET 0
+#define CONFIG_ENV_SIZE 2048
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
#endif
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register 5-5
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
-#define CFG_RMR RMR_CSRE
+#define CONFIG_SYS_RMR RMR_CSRE
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
#define BCR_APD01 0x10000000
-#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR (SIUMCR_BBD|SIUMCR_APPC10|\
+#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_APPC10|\
SIUMCR_CS10PC00|SIUMCR_BCTLC10)
/*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
* Ensure DFBRG is Divide by 16
*/
-#define CFG_SCCR SCCR_DFBRG01
+#define CONFIG_SYS_SCCR SCCR_DFBRG01
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
-#define CFG_MIN_AM_MASK 0xC0000000
+#define CONFIG_SYS_MIN_AM_MASK 0xC0000000
/*-----------------------------------------------------------------------
* MPTPR - Memory Refresh Timer Prescaler Register 10-18
*-----------------------------------------------------------------------
*/
-#define CFG_MPTPR 0x1F00
+#define CONFIG_SYS_MPTPR 0x1F00
/*-----------------------------------------------------------------------
* PSRT - Refresh Timer Register 10-16
*-----------------------------------------------------------------------
*/
-#define CFG_PSRT 0x0f
+#define CONFIG_SYS_PSRT 0x0f
/*-----------------------------------------------------------------------
* PSRT - SDRAM Mode Register 10-10
/* SDRAM initialization values for 8-column chips
*/
-#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\
+#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A7 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_8COL (PSDMR_PBI |\
+#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\
PSDMR_SDAM_A15_IS_A5 |\
PSDMR_BSMA_A15_A17 |\
PSDMR_SDA10_PBI1_A7 |\
/* SDRAM initialization values for 9-column chips
*/
-#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\
+#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A6 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_9COL (PSDMR_PBI |\
+#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\
PSDMR_SDAM_A16_IS_A5 |\
PSDMR_BSMA_A15_A17 |\
PSDMR_SDA10_PBI1_A6 |\
*
*/
-#define CFG_MRS_OFFS 0x00000000
+#define CONFIG_SYS_MRS_OFFS 0x00000000
/* Bank 0 - FLASH
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_3_CLK |\
/* Bank 2 - 60x bus SDRAM
*/
-#ifndef CFG_RAMBOOT
-#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+#ifndef CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR2_PRELIM CFG_OR2_8COL
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL
-#define CFG_PSDMR CFG_PSDMR_8COL
-#endif /* CFG_RAMBOOT */
+#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_8COL
+#endif /* CONFIG_SYS_RAMBOOT */
-#define CFG_BR4_PRELIM ((RTC_BASE_ADDR & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR4_PRELIM ((RTC_BASE_ADDR & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_UPMA |\
BRx_V)
-#define CFG_OR4_PRELIM (ORxU_AM_MSK | ORxU_BI)
+#define CONFIG_SYS_OR4_PRELIM (ORxU_AM_MSK | ORxU_BI)
/*-----------------------------------------------------------------------
* PCMCIA stuff
*/
#define CONFIG_I82365
-#define CFG_PCMCIA_MEM_ADDR 0x81000000
-#define CFG_PCMCIA_MEM_SIZE 0x1000
+#define CONFIG_SYS_PCMCIA_MEM_ADDR 0x81000000
+#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x1000
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR 0xa0000000
+#define CONFIG_SYS_ATA_BASE_ADDR 0xa0000000
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET 0x100
+#define CONFIG_SYS_ATA_DATA_OFFSET 0x100
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET 0x100
+#define CONFIG_SYS_ATA_REG_OFFSET 0x100
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x108
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x108
#endif /* __CONFIG_H */