#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
/*
* DDR related
*/
-#define CONFIG_OMAP3_MICRON_DDR 1 /* Micron DDR */
#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
/*
#define CONFIG_CMD_MMC /* MMC support */
#define CONFIG_CMD_NAND /* NAND support */
#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
+#undef CONFIG_CMD_PING
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#define CONFIG_JFFS2_NAND
/* nand device jffs2 lives on */
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc rescan ${mmcdev}; then " \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT V_PROMPT
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
-#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
-#endif
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*-----------------------------------------------------------------------
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
+
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE 0x40200800
+#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
+#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
+
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
+ 10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+
#endif /* __CONFIG_H */