#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC512X 1 /* MPC512X family */
#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */
+#undef CONFIG_FSL_DIU_LOGO_BMP /* Don't include FSL DIU binary bmp */
/* video */
#undef CONFIG_VIDEO
#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#endif
+/*
+ * IIM - IC Identification Module
+ */
+#undef CONFIG_IIM
+
/*
* EEPROM configuration
*/
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DATE
+#undef CONFIG_CMD_FUSE
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_EXT2
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
+#if defined(CONFIG_CMD_IDE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION
+#endif /* defined(CONFIG_CMD_IDE) */
+
/*
* Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
* For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
#endif
#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | HID0_ICE)
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc@80000000/serial@11300"
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for IDE not supported */
+
+#define CONFIG_IDE_RESET /* reset for IDE supported */
+#define CONFIG_IDE_PREINIT
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR MPC512X_PATA
+
+/* Offset for data I/O RefMan MPC5121EE Table 28-10 */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x00A0)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers RefMan MPC5121EE Table 28-23 */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x00D8)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#define ATA_BASE_ADDR MPC512X_PATA
+
+/*
+ * Control register bit definitions
+ */
+#define FSL_ATA_CTRL_FIFO_RST_B 0x80000000
+#define FSL_ATA_CTRL_ATA_RST_B 0x40000000
+#define FSL_ATA_CTRL_FIFO_TX_EN 0x20000000
+#define FSL_ATA_CTRL_FIFO_RCV_EN 0x10000000
+#define FSL_ATA_CTRL_DMA_PENDING 0x08000000
+#define FSL_ATA_CTRL_DMA_ULTRA 0x04000000
+#define FSL_ATA_CTRL_DMA_WRITE 0x02000000
+#define FSL_ATA_CTRL_IORDY_EN 0x01000000
+
#endif /* __CONFIG_H */