* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
-
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
-#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_CPLD_BASE 0x80000000
#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
+#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
+
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
#define CFG_TEMP_STACK_OCM 1 /* OCM as init ram */
/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR 0xF8000000
+#define CFG_OCM_DATA_ADDR 0xf8000000
#define CFG_OCM_DATA_SIZE 0x4000 /* 16K of onchip SRAM */
#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SRAM */
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define _CFG_CMD_INCLUDE (CFG_CMD_ALL)
#else
#define CFG_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */
-#define _CFG_CMD_INCLUDE ((CFG_CMD_ALL) & ~(CFG_CMD_FLASH | CFG_CMD_IMLS))
#endif
#ifdef CFG_ENV_IS_IN_FLASH
*/
#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_DATA_ADDR + (12 << 10)) /* Copy SPL here*/
+#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_NET_MULTI 1
#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
+#define CONFIG_HAS_ETH0 1
#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
+#define xstr(s) str(s)
+#define str(s) #s
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=acadia\0" \
"ramdisk_addr=fff20000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 acadia/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b ${fileaddr} fffc0000 ${filesize};" \
+ "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
+ "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
"setenv filesize;saveenv\0" \
"upd=run load update\0" \
"nload=tftp 200000 acadia/u-boot-nand.bin\0" \
#define CONFIG_SUPPORT_VFAT
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & _CFG_CMD_INCLUDE) | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DTT | \
- CFG_CMD_DIAG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NAND | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_USB)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_USB
+
+/*
+ * No NOR on Acadia when NAND-booting
+ */
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
*----------------------------------------------------------------------*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EZ CPU */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/
-#endif
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff