/*
- * (C) Copyright 2000, 2001, 2002
+ * (C) Copyright 2000-2008
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOARD_TYPES 1 /* support board types */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_8xx\0" \
- "bootfile=/tftpboot/TQM860L/uImage\0" \
- "kernel_addr=40040000\0" \
- "ramdisk_addr=40100000\0" \
+ "hostname=TQM860L\0" \
+ "bootfile=TQM860L/uImage\0" \
+ "fdt_addr=40040000\0" \
+ "kernel_addr=40060000\0" \
+ "ramdisk_addr=40200000\0" \
+ "u-boot=TQM860L/u-image.bin\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "update=prot off 40000000 +${filesize};" \
+ "era 40000000 +${filesize};" \
+ "cp.b 200000 40000000 ${filesize};" \
+ "sete filesize;save\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_ELF | \
- CFG_CMD_IDE | \
- CFG_CMD_DATE )
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
+
+#define CONFIG_NETCONSOLE
/*
* Miscellaneous configurable options
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if 0
-#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-#endif
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+/* use CFI flash driver */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE+flash_info[0].size }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
+
+/*-----------------------------------------------------------------------
+ * Dynamic MTD partition support
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=TQM8xxL-0"
+
+#define MTDPARTS_DEFAULT "mtdparts=TQM8xxL-0:256k(u-boot)," \
+ "128k(dtb)," \
+ "1664k(kernel)," \
+ "2m(rootfs)," \
+ "4m(data)"
+
/*-----------------------------------------------------------------------
* Hardware Information Block
*/
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
-#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR \
- ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else /* up to 50 MHz we use a 1:1 clock */
#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif /* CONFIG_80MHz */
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
-#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR (/* SCCR_TBS | */ \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
-#else /* up to 50 MHz we use a 1:1 clock */
-#define CFG_SCCR (SCCR_TBS | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-#endif /* CONFIG_80MHz */
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
-/*#define CFG_DER 0x2002000F*/
#define CFG_DER 0
/*
/*
* FLASH timing:
*/
-#if defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | 0 | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else /* 50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif /*CONFIG_??MHz */
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
* 66 Mhz => 66.000.000 / Divider = 129
* 80 Mhz => 80.000.000 / Divider = 156
*/
-#if defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA 156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA 129
-#else /* 50 MHz */
-#define CFG_MAMR_PTA 98
-#endif /*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA 98
/*
* For 16 MBit, refresh rates could be 31.3 us