#undef CONFIG_CONS_NONE /* define if console on something else */
#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-#else
+#else /* ! TQM8560 */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
-#endif /* CONFIG_TQM8560 */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
/* PS/2 Keyboard */
+#if !defined(CONFIG_TQM8560)
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */
#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
#define CONFIG_BOARD_EARLY_INIT_R 1
+#endif /* !CONFIG_TQM8560 */
+
+#endif /* CONFIG_TQM8560 */
+
+#define CONFIG_BAUDRATE 115200
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
"run nfsargs addip addcons;bootm\0" \
"rootpath=/opt/eldk/ppc_85xx\0" \
"kernel_addr=FE000000\0" \
- "ramdisk_addr=FE100000\0" \
+ "ramdisk_addr=FE180000\0" \
"load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \