/*
+ * (C) Copyright 2007
+ * Thomas Waehner, TQ-System GmbH, thomas.waehner@tqs.de.
+ *
* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
*/
/*
- * TQM85xx (8560/40/55/41) board configuration file
+ * TQM85xx (8560/40/55/41/48) board configuration file
*/
#ifndef __CONFIG_H
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
#define CONFIG_PCI
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */
+#ifdef CONFIG_TQM8548
+#define CONFIG_PCI1
+#define CONFIG_PCIE1
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#endif
+
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+ /*
+ * Configuration for big NOR Flashes
+ *
+ * Define CONFIG_TQM_BIGFLASH for boards with more than 128 MiB NOR Flash.
+ * Please be aware, that this changes the whole memory map (new CCSRBAR
+ * address, etc). You have to use an adapted Linux kernel or FDT blob
+ * if this option is set.
+ */
+#undef CONFIG_TQM_BIGFLASH
+
/*
- * Only MPC8540 doesn't have CPM module
+ * NAND flash support (disabled by default)
+ *
+ * Warning: NAND support will likely increase the U-Boot image size
+ * to more than 256 KB. Please adjust TEXT_BASE if necessary.
*/
-#ifndef CONFIG_MPC8540
+#undef CONFIG_NAND
+
+/*
+ * MPC8540 and MPC8548 don't have CPM module
+ */
+#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548)
#define CONFIG_CPM2 1 /* has CPM2 */
#endif
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support */
+
/*
* sysclk for MPC85xx
*
* Two valid values are:
- * 33000000
- * 66000000
+ * 33333333
+ * 66666666
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
* is likely the desired value here, so that is now the default.
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
+#ifdef CONFIG_TQM_BIGFLASH
+#define CFG_CCSRBAR 0xA0000000 /* relocated CCSRBAR */
+#else /* !CONFIG_TQM_BIGFLASH */
#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
+#endif /* CONFIG_TQM_BIGFLASH */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_PCI1_ADDR (CFG_CCSRBAR + 0x8000)
+#define CFG_PCI2_ADDR (CFG_CCSRBAR + 0x9000)
+#define CFG_PCIE1_ADDR (CFG_CCSRBAR + 0xa000)
+
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CONFIG_ADD_RAM_INFO 1 /* print additional info*/
#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
/* TQM8540 & 8560 need DLL-override */
#define CONFIG_DDR_DLL /* DLL fix needed */
#define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */
-#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */
+#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */
-#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555)
+#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) || \
+ defined(CONFIG_TQM8548)
#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
-#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */
+#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */
+
+/*
+ * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM
+ * series while new boards have 'N' type Flashes from the S29GLxxxN
+ * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
+ */
+#ifdef CONFIG_TQM8548
+#define CONFIG_TQM_FLASH_N_TYPE
+#endif /* CONFIG_TQM8548 */
/*
* Flash on the Local Bus
*/
+#ifdef CONFIG_TQM_BIGFLASH
+#define CFG_FLASH0 0xE0000000
+#define CFG_FLASH1 0xC0000000
+#else /* !CONFIG_TQM_BIGFLASH */
#define CFG_FLASH0 0xFC000000
#define CFG_FLASH1 0xF8000000
+#endif /* CONFIG_TQM_BIGFLASH */
#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */
-#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */
+#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */
+/* Default ORx timings are for <= 41.7 MHz Local Bus Clock.
+ *
+ * Note: According to timing specifications external addr latch delay
+ * (EAD, bit #0) must be set if Local Bus Clock is > 83 MHz.
+ *
+ * For other Local Bus Clocks see following table:
+ *
+ * Clock/MHz CFG_ORx_PRELIM
+ * 166 0x.....CA5
+ * 133 0x.....C85
+ * 100 0x.....C65
+ * 83 0x.....FA2
+ * 66 0x.....C82
+ * 50 0x.....C60
+ * 42 0x.....040
+ * 33 0x.....030
+ * 25 0x.....020
+ *
+ */
+#ifdef CONFIG_TQM_BIGFLASH
+#define CFG_BR0_PRELIM 0xE0001801 /* port size 32bit */
+#define CFG_OR0_PRELIM 0xE0000040 /* 512MB Flash */
+#define CFG_BR1_PRELIM 0xC0001801 /* port size 32bit */
+#define CFG_OR1_PRELIM 0xE0000040 /* 512MB Flash */
+#else /* !CONFIG_TQM_BIGFLASH */
#define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */
#define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */
#define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */
#define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */
+#endif /* CONFIG_TQM_BIGFLASH */
-#define CFG_FLASH_CFI /* flash is CFI compat. */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
+#define CFG_FLASH_CFI /* flash is CFI compat. */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 512 /* sectors per device */
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 512 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
+/*
+ * Note: when changing the Local Bus clock divider you have to
+ * change the timing values in CFG_ORx_PRELIM.
+ *
+ * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8.
+ * LCRR[16:17] EADC : External address delay cycles. It should be set to 2
+ * for Local Bus Clock > 83.3 MHz.
+ */
+#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR (CFG_CCSRBAR \
+ + 0x04010000) /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */
+#define CFG_MALLOC_LEN (384 * 1024) /* Reserved for malloc */
/* Serial Port */
#if defined(CONFIG_TQM8560)
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-#else /* ! TQM8560 */
+#else /* !CONFIG_TQM8560 */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* PS/2 Keyboard */
-#if !defined(CONFIG_TQM8560)
#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */
#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
#define CONFIG_BOARD_EARLY_INIT_R 1
-#endif /* !CONFIG_TQM8560 */
#endif /* CONFIG_TQM8560 */
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/* CAN */
+#define CFG_CAN_BASE (CFG_CCSRBAR \
+ + 0x03000000) /* CAN base address */
+#ifdef CONFIG_CAN_DRIVER
+#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */
+#define CFG_OR2_CAN (CFG_CAN_OR_AM | OR_UPM_BI)
+#define CFG_BR2_CAN ((CFG_CAN_BASE & BR_BA) | \
+ BR_PS_8 | BR_MS_UPMC | BR_V)
+#endif /* CONFIG_CAN_DRIVER */
/*
* I2C
*/
-#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
+#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
+#ifndef CONFIG_PCIE1
/* RapidIO MMU */
+#ifdef CONFIG_TQM_BIGFLASH
+#define CFG_RIO_MEM_BASE 0xb0000000 /* base address */
+#define CFG_RIO_MEM_SIZE 0x10000000 /* 256M */
+#else /* !CONFIG_TQM_BIGFLASH */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
+#endif /* CONFIG_TQM_BIGFLASH */
#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+#endif /* CONFIG_PCIE1 */
+
+/* NAND FLASH */
+#ifdef CONFIG_NAND
+
+#undef CONFIG_NAND_LEGACY
+
+#define CONFIG_NAND_FSL_UPM 1
+
+#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */
+
+/* address distance between chip selects */
+#define CFG_NAND_SELECT_DEVICE 1
+#define CFG_NAND_CS_DIST 0x200
+
+#define CFG_NAND_SIZE 0x8000
+#define CFG_NAND0_BASE (CFG_CCSRBAR + 0x03010000)
+#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST)
+#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST)
+#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST)
+
+#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
+#define NAND_MAX_CHIPS 1
+
+#if (CFG_MAX_NAND_DEVICE == 1)
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE }
+#elif (CFG_MAX_NAND_DEVICE == 2)
+#define CFG_NAND_QUIET_TEST 1
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \
+ CFG_NAND1_BASE, \
+}
+#elif (CFG_MAX_NAND_DEVICE == 4)
+#define CFG_NAND_QUIET_TEST 1
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \
+ CFG_NAND1_BASE, \
+ CFG_NAND2_BASE, \
+ CFG_NAND3_BASE, \
+}
+#endif
+
+/* CS3 for NAND Flash */
+#define CFG_BR3_PRELIM ((CFG_NAND0_BASE & BR_BA) | BR_PS_8 | \
+ BR_MS_UPMB | BR_V)
+#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_NAND_SIZE) | OR_UPM_BI)
+
+#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */
+
+#endif /* CONFIG_NAND */
/*
* General PCI
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_BASE (CFG_CCSRBAR + 0x02000000)
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+#ifdef CONFIG_PCIE1
+/*
+ * General PCI express
+ * Addresses are mapped 1-1.
+ */
+#ifdef CONFIG_TQM_BIGFLASH
+#define CFG_PCIE1_MEM_BASE 0xb0000000
+#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 512M */
+#define CFG_PCIE1_IO_BASE 0xaf000000
+#else /* !CONFIG_TQM_BIGFLASH */
+#define CFG_PCIE1_MEM_BASE 0xc0000000
+#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCIE1_IO_BASE 0xef000000
+#endif /* CONFIG_TQM_BIGFLASH */
+#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_IO_PHYS CFG_PCIE1_IO_BASE
+#define CFG_PCIE1_IO_SIZE 0x1000000 /* 16M */
+#endif /* CONFIG_PCIE1 */
#if defined(CONFIG_PCI)
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#endif /* CONFIG_PCI */
-
+#endif /* CONFIG_PCI */
#define CONFIG_NET_MULTI 1
#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
#define FEC_FLAGS 0
+#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
+#ifdef CONFIG_TQM8548
+/*
+ * TQM8548 has 4 ethernet ports. 4 ETSEC's.
+ *
+ * On the STK85xx Starterkit the ETSEC3/4 ports are on an
+ * additional adapter (AIO) between module and Starterkit.
+ */
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "TSEC2"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "TSEC3"
+#define TSEC3_PHY_ADDR 4
+#define TSEC4_PHY_ADDR 5
+#define TSEC3_PHYIDX 0
+#define TSEC4_PHYIDX 0
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define CONFIG_HAS_ETH3
+#define CONFIG_HAS_ETH4
+#endif /* CONFIG_TQM8548 */
+
/* Options are TSEC[0-1], FEC */
#define CONFIG_ETHPRIME "TSEC0"
* FCC2: a - c (X50.2 - 1)
*/
#define CONFIG_ETHER_ON_FCC
-#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */
+#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */
#endif
#if defined(CONFIG_TQM8560)
* FCC3: a - d (X50.2 - 3)
*/
#define CONFIG_ETHER_ON_FCC
-#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */
+#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */
#endif
#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
#define CONFIG_ETHER_ON_FCC1
-#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \
+ CMXFCR_TF1CS_MSK)
#define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
#define CFG_CPMFCR_RAMTYPE 0
#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
#define CONFIG_ETHER_ON_FCC2
-#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \
+ CMXFCR_TF2CS_MSK)
#define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13)
#define CFG_CPMFCR_RAMTYPE 0
#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
#define CONFIG_ETHER_ON_FCC3
-#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \
+ CMXFCR_TF3CS_MSK)
#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
#define CFG_CPMFCR_RAMTYPE 0
#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
* Environment
*/
#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000)
-#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+
+#ifdef CONFIG_TQM_FLASH_N_TYPE
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */
+#else /* !CONFIG_TQM_FLASH_N_TYPE */
+#define CFG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
+#endif /* CONFIG_TQM_FLASH_N_TYPE */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_TIMESTAMP /* Print image info with ts */
-
+#define CONFIG_TIMESTAMP /* Print image info with ts */
/*
* BOOTP options
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
+#ifdef CONFIG_NAND
+/*
+ * Use NAND-FLash as JFFS2 device
+ */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_JFFS2
+
+#define CONFIG_JFFS2_NAND 1
+
+#ifdef CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nand0=TQM85xx-nand"
+#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-"
+#else
+#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */
+#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */
+#endif /* CONFIG_JFFS2_CMDLINE */
+
+#endif /* CONFIG_NAND */
/*
* Command line configuration.
#define CONFIG_CMD_MII
#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI
#endif
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */
+#define CFG_PBSIZE (CFG_CBSIZE + \
+ sizeof(CFG_PROMPT) + 16) /* Print Buf Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
-#endif
-
/*
* Internal Definitions
*
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-
#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+/*
+ * Setup some board specific values for the default environment variables
+ */
+#ifdef CONFIG_CPM2
+#define CFG_ENV_CONSDEV "consdev=ttyCPM0\0"
+#else
+#define CFG_ENV_CONSDEV "consdev=ttyS0\0"
+#endif
+#define CFG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \
+ MK_STR(CONFIG_HOSTNAME)".dtb\0"
+#define CFG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0"
+#define CFG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \
+ "uboot_addr="MK_STR(TEXT_BASE)"\0"
+
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
+ CFG_ENV_BOOTFILE \
+ CFG_ENV_FDT_FILE \
+ CFG_ENV_CONSDEV \
"netdev=eth0\0" \
- "consdev=ttyS0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addcons=setenv bootargs $bootargs " \
"console=$consdev,$baudrate\0" \
"flash_nfs=run nfsargs addip addcons;" \
- "bootm $kernel_addr\0" \
+ "bootm $kernel_addr - $fdt_addr\0" \
"flash_self=run ramargs addip addcons;" \
- "bootm $kernel_addr $ramdisk_addr\0" \
- "net_nfs=tftp $loadaddr $bootfile;" \
- "run nfsargs addip addcons;bootm\0" \
+ "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \
+ "net_nfs=tftp $kernel_addr_r $bootfile;" \
+ "tftp $fdt_addr_r $fdt_file;" \
+ "run nfsargs addip addcons;" \
+ "bootm $kernel_addr_r - $fdt_addr_r\0" \
"rootpath=/opt/eldk/ppc_85xx\0" \
- "kernel_addr=FE000000\0" \
- "ramdisk_addr=FE180000\0" \
- "load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
+ "fdt_addr_r=900000\0" \
+ "kernel_addr_r=1000000\0" \
+ "fdt_addr=ffec0000\0" \
+ "kernel_addr=ffd00000\0" \
+ "ramdisk_addr=ff800000\0" \
+ CFG_ENV_UBOOT \
+ "load=tftp 100000 $uboot\0" \
+ "update=protect off $uboot_addr +$filesize;" \
+ "erase $uboot_addr +$filesize;" \
+ "cp.b 100000 $uboot_addr $filesize;" \
"setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
-#endif /* __CONFIG_H */
+#endif /* __CONFIG_H */