/*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * (C) Copyright 2004
+ * (C) Copyright 2004-2005
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
*
* See file CREDITS for list of people who contributed to this
#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG 1
-
/*
* High Level Configuration Options
* (easy to change)
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
+#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
+#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#ifdef CONFIG_STK52XX
+#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
+#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+#define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+#define CONFIG_BOARD_EARLY_INIT_R
+#endif /* CONFIG_STK52XX */
-#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
-#define CONFIG_PCI 0
+#ifdef CONFIG_STK52XX
+#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
+/* #define CONFIG_PCI_SCAN_SHOW 1 */
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_NET_MULTI 1
-#define CONFIG_EEPRO100 1
+#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
+#endif /* CONFIG_STK52XX */
-#define ADD_PCI_CMD 0 /* CFG_CMD_PCI */
-
-#else /* MPC5100 */
+#ifdef CONFIG_PCI
+#define ADD_PCI_CMD CFG_CMD_PCI
+#else
+#define ADD_PCI_CMD 0
+#endif
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
+/*
+ * Video console
+ */
+#if 1
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_SM501
+#define CONFIG_VIDEO_SM501_32BPP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#define CFG_CONSOLE_IS_IN_ENV
+#endif
+#ifdef CONFIG_VIDEO
+#define ADD_BMP_CMD CFG_CMD_BMP
+#else
+#define ADD_BMP_CMD 0
#endif
/* Partitions */
-#undef CONFIG_MAC_PARTITION
-#if defined (CONFIG_MINIFAP)
+#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-#endif
+#define CONFIG_ISO_PARTITION
/* USB */
-#if 0
+#ifdef CONFIG_STK52XX
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
#else
-#define ADD_USB_CMD 0
+#define ADD_USB_CMD 0
#endif
/* POST support */
#endif
/* IDE */
-#if defined (CONFIG_MINIFAP)
-#define ADD_IDE_CMD CFG_CMD_IDE | CFG_CMD_FAT
+#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
+#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
#else
#define ADD_IDE_CMD 0
#endif
* Supported commands
*/
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
+ ADD_BMP_CMD | \
+ ADD_IDE_CMD | \
ADD_PCI_CMD | \
ADD_USB_CMD | \
- CFG_CMD_POST_DIAG | \
+ CFG_CMD_ASKENV | \
CFG_CMD_DATE | \
- CFG_CMD_REGINFO | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ECHO | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
+ CFG_CMD_JFFS2 | \
CFG_CMD_MII | \
+ CFG_CMD_NFS | \
CFG_CMD_PING | \
- ADD_IDE_CMD)
+ CFG_CMD_POST_DIAG | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SNTP | \
+ CFG_CMD_BSP)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#define CONFIG_TIMESTAMP /* display image timestamps */
+
#if (TEXT_BASE == 0xFC000000) /* Boot low */
-# define CFG_LOWBOOT 1
+# define CFG_LOWBOOT 1
#endif
/*
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_PREBOOT "echo;" \
+#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#if defined (CONFIG_TQM5200_AA)
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
- "bootfile=uImage_tqm5200_mkr\0" \
- "load=tftp 200000 $(loadfile)\0" \
- "load133=tftp 200000 $(loadfile133)\0" \
- "loadfile=u-boot_tqm5200_aa_mkr.bin\0" \
- "loadfile133=u-boot_tqm5200_aa_133_mkr.bin\0" \
- "update=protect off 1:0-4; erase 1:0-4; cp.b 200000 0xfc000000 $(filesize); protect on 1:0-4\0" \
- "serverip=172.20.5.13\0" \
- ""
+# define CONFIG_U_BOOT_SUFFIX "-AA\0"
+#elif defined (CONFIG_TQM5200_AB)
+# define CONFIG_U_BOOT_SUFFIX "-AB\0"
+#elif defined (CONFIG_TQM5200_AC)
+# define CONFIG_U_BOOT_SUFFIX "-AC\0"
#else
-#if defined (CONFIG_TQM5200_AB)
-#define CONFIG_EXTRA_ENV_SETTINGS \
+# define CONFIG_U_BOOT_SUFFIX "\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
- "bootfile=uImage_tqm5200_mkr\0" \
- "load=tftp 200000 $(loadfile)\0" \
- "load133=tftp 200000 $(loadfile133)\0" \
- "loadfile=u-boot_tqm5200_ab_mkr.bin\0" \
- "loadfile133=u-boot_tqm5200_ab_133_mkr.bin\0" \
- "update=protect off 1:0-1; erase 1:0-1; cp.b 200000 0xfc000000 $(filesize); protect on 1:0-1\0" \
- "serverip=172.20.5.13\0" \
- ""
-#else
-#if defined (CONFIG_TQM5200_AC)
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
- "bootfile=uImage_tqm5200_mkr\0" \
- "load=tftp 200000 $(loadfile)\0" \
- "load133=tftp 200000 $(loadfile133)\0" \
- "loadfile=u-boot_tqm5200_ac_mkr.bin\0" \
- "loadfile133=u-boot_tqm5200_ac_133_mkr.bin\0" \
- "update=protect off 1:0-4; erase 1:0-4; cp.b 200000 0xfc000000 $(filesize); protect on 1:0-4\0" \
- "serverip=172.20.5.13\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin" CONFIG_U_BOOT_SUFFIX \
+ "update=protect off FC000000 FC05FFFF;" \
+ "erase FC000000 FC05FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC05FFFF\0" \
""
-#endif
-#endif
-#endif
#define CONFIG_BOOTCOMMAND "run net_nfs"
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBSPEED_133 /* define for 133MHz speed */
#if defined(CFG_IPBSPEED_133)
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#if defined (CONFIG_MINIFAP)
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#ifdef CONFIG_TQM5200_REV100
+#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */
#else
-#define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */
+#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */
#endif
/*
*/
#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AC)
-#define CFG_FLASH_SIZE 0x00400000 /* 4 MByte */
-#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */
-#else
-#ifdef CONFIG_TQM5200_AB
-#define CFG_FLASH_SIZE 0x02000000 /* 32 MByte */
-#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
-#endif
-#endif
+/* use CFI flash driver if no module variant is spezified */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00740000 + 0x00800000)
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
#else /* CFG_LOWBOOT */
-#if defined(CONFIG_TQM5200_AA) || defined(CONFIG_TQM5200_AB) || \
- defined (CONFIG_TQM5200_AC)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000)
-#endif
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
#endif /* CFG_LOWBOOT */
#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+/* Dynamic MTD partition support */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
+ "1408k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
/*
* Environment settings
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_SIZE 0x10000
#define CFG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OVERWRITE 1
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Memory map
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
* Bit 0 (mask: 0x80000000): 1
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- * 00 -> No Alternatives, I2C1 is used for onboard EEPROM
- * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
- * EEPROM
+ * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
+ * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
+ * Use for REV200 STK52XX boards. Do not use with REV100 modules
+ * (because, there I2C1 is used as I2C bus)
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
- * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
- * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
- * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- * tests.
+ * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
+ * 000 -> All PSC2 pins are GIOPs
+ * 001 -> CAN1/2 on PSC2 pins
+ * Use for REV100 STK52xx boards
+ * use PSC6:
+ * on STK52xx:
+ * use as UART. Pins PSC6_0 to PSC6_3 are used.
+ * Bits 9:11 (mask: 0x00700000):
+ * 101 -> PSC6 : Extended POST test is not available
+ * on MINI-FAP and TQM5200_IB:
+ * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ * 000 -> PSC6 could not be used as UART, CODEC or IrDA
+ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
+ * tests.
*/
#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG 0x93000004
-#else
-#define CFG_GPS_PORT_CONFIG 0x83000004
+# define CFG_GPS_PORT_CONFIG 0x91000004
+#elif defined (CONFIG_STK52XX)
+# if defined (CONFIG_STK52XX_REV100)
+# define CFG_GPS_PORT_CONFIG 0x81500014
+# else /* STK52xx REV200 and above */
+# if defined (CONFIG_TQM5200_REV100)
+# error TQM5200 REV100 not supported on STK52XX REV200 or above
+# else/* TQM5200 REV200 and above */
+# define CFG_GPS_PORT_CONFIG 0x91500004
+# endif
+# endif
+#else /* TMQ5200 Inbetriebnahme-Board */
+# define CFG_GPS_PORT_CONFIG 0x81000004
#endif
/*
* RTC configuration
*/
-#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
+#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100)
+# define CONFIG_RTC_M41T11 1
+# define CFG_I2C_RTC_ADDR 0x68
+#else
+# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
+#endif
/*
* Miscellaneous configurable options
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
+/* automatic configuration of chip selects */
+#ifdef CONFIG_CS_AUTOCONF
+#define CONFIG_LAST_STAGE_INIT
+#endif
+
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#ifdef CONFIG_TQM5200_AB
+#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
+#ifdef CONFIG_TQM5200_AB
#define CFG_CS2_SIZE 0x80000 /* 512 kByte */
+#else /* CONFIG_CS_AUTOCONF */
+#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
+#endif
#define CFG_CS2_CFG 0x0004D930
#endif
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC)
-#define CFG_CS1_START 0xE0000000
+#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
+ defined (CONFIG_CS_AUTOCONF)
+#define SM501_FB_BASE 0xE0000000
+#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
-#define CFG_CS1_CFG 0x0148FF70
+#define CFG_CS1_CFG 0x8F48FF70
#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
#endif
#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
#define CFG_RESET_ADDRESS 0xff000000
*-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
-#define CONFIG_IDE_RESET /* reset for ide supported */
+#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET (0x005C)
-/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+/* Interval between registers */
+#define CFG_ATA_STRIDE 4
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff