#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#define CONFIG_TB5200 1 /* ... on a TB5200 base board */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
#define CONFIG_SERIAL_MULTI 1 /* support multiple consoles */
#define CONFIG_PSC_CONSOLE2 6 /* second console is on PSC6 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* Video console
#define CONFIG_CONSOLE_EXTRA_INFO
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
-#define CFG_CONSOLE_IS_IN_ENV
-#endif
-
-#ifdef CONFIG_VIDEO
-#define ADD_BMP_CMD CFG_CMD_BMP
-#else
-#define ADD_BMP_CMD 0
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#endif
/* Partitions */
/* USB */
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
/* POST support */
-#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_I2C)
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_I2C)
#ifdef CONFIG_POST
-#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
/* preserve space for the post_word at end of on-chip SRAM */
#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#else
-#define CFG_CMD_POST_DIAG 0
#endif
-/* IDE */
-#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
/*
- * Supported commands
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_BMP_CMD | \
- ADD_IDE_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_NFS | \
- CFG_CMD_PING | \
- CFG_CMD_POST_DIAG | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SNTP | \
- CFG_CMD_BSP)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_USB
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_POST
+#define CONFIG__CMD_DIAG
+#endif
+
#define CONFIG_TIMESTAMP /* display image timestamps */
#if (TEXT_BASE == 0xFC000000) /* Boot low */
-# define CFG_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT 1
#endif
/*
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "rootpath=/opt/eldk/ppc_6xx\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "update=protect off FC000000 FC07FFFF;" \
+ "erase FC000000 FC07FFFF;" \
+ "cp.b 200000 FC000000 ${filesize};" \
+ "protect on FC000000 FC07FFFF\0" \
+ ""
+#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"cp.b 200000 FC000000 ${filesize};" \
"protect on FC000000 FC05FFFF\0" \
""
+#endif /* CONFIG_TQM5200_B */
#define CONFIG_BOOTCOMMAND "run net_nfs"
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133)
+#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
+ * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #2 */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
/*
* I2C clock frequency
* Please notice, that the resulting clock frequency could differ from the
* configured value. This is because the I2C clock is derived from system
* clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CFG_I2C_SPEED. However the calculated
+ * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
* approximation allways lies below the configured value, never above.
*/
-#define CFG_I2C_SPEED 100000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
* EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
* same configuration could be used.
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/* List of I2C addresses to be verified by POST */
#undef I2C_ADDR_LIST
-#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
- CFG_I2C_RTC_ADDR, \
- CFG_I2C_SLAVE }
+#define I2C_ADDR_LIST { CONFIG_SYS_I2C_EEPROM_ADDR, \
+ CONFIG_SYS_I2C_RTC_ADDR, \
+ CONFIG_SYS_I2C_SLAVE }
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
-
-/* use CFI flash driver if no module variant is spezified */
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */
-#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CFG_FLASH_USE_BUFFER_WRITE 1
-
-#if !defined(CFG_LOWBOOT)
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000)
-#else /* CFG_LOWBOOT */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000)
-#endif /* CFG_LOWBOOT */
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
+#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */
+
+/* use CFI flash driver */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
+
+#if !defined(CONFIG_SYS_LOWBOOT)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
+#else /* CONFIG_SYS_LOWBOOT */
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00080000)
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
+#endif /* CONFIG_TQM5200_B */
+#endif /* CONFIG_SYS_LOWBOOT */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=TQM5200-0"
+#if defined(CONFIG_TQM5200_B)
+#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:768k(firmware)," \
+ "1280k(kernel)," \
+ "2m(initrd)," \
+ "4m(small-fs)," \
+ "16m(big-fs)," \
+ "8m(misc)"
+#else
#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
"1408k(kernel)," \
"2m(initrd)," \
"4m(small-fs)," \
"16m(big-fs)," \
"8m(misc)"
+#endif /* CONFIG_TQM5200_B */
/*
* Environment settings
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x10000
-#define CFG_ENV_SECT_SIZE 0x20000
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#else
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_TQM5200_B */
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use ON-Chip SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
#else
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
#endif
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#if defined(CONFIG_TQM5200_B)
+#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#else
+#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#endif /* CONFIG_TQM5200_B */
+#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* Reserve 1024 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
+#define CONFIG_MPC5xxx_FEC_MII100
/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
*/
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR 0x00
/*
* GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
* tests.
*/
-#define CFG_GPS_PORT_CONFIG 0x81500114
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500114
/*
* RTC configuration
*/
#define CONFIG_RTC_M41T11 1
-#define CFG_I2C_RTC_ADDR 0x68
-#define CFG_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base
year */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
/* Enable an alternate, more extensive memory test */
-#define CFG_ALT_MEMTEST
+#define CONFIG_SYS_ALT_MEMTEST
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
- * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
- * which is normally part of the default commands (CFV_CMD_DFL)
+ * Enable loopw command.
*/
#define CONFIG_LOOPW
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL 0
#endif
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
-#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
+#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
-#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
+#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
#endif
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-/* automatic configuration of chip selects */
-#ifdef CONFIG_CS_AUTOCONF
#define CONFIG_LAST_STAGE_INIT
-#endif
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
-#define CFG_CS2_START 0xE5000000
-#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
-#define CFG_CS2_CFG 0x0004D930
-#endif
+#define CONFIG_SYS_CS2_START 0xE5000000
+#define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
+#define CONFIG_SYS_CS2_CFG 0x0004D930
/*
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_CS_AUTOCONF)
#define SM501_FB_BASE 0xE0000000
-#define CFG_CS1_START (SM501_FB_BASE)
-#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
-#define CFG_CS1_CFG 0x8F48FF70
-#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
-#endif
+#define CONFIG_SYS_CS1_START (SM501_FB_BASE)
+#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
+#define CONFIG_SYS_CS1_CFG 0x8F48FF70
+#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */
-#define CFG_RESET_ADDRESS 0xff000000
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*-----------------------------------------------------------------------
* USB stuff
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CONFIG_SYS_ATA_STRIDE 4
#endif /* __CONFIG_H */