apalis/colibri imx6: provide proper fdtfile value

[oweals/u-boot.git] / include / configs / T102xRDB.h

diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
index 733e44f75c7b59e76267bdfeb3b987b4db7d9a66..d90181f12ae77462215c0faee07eb8b8ef1c9ca2 100644 (file)
--- a/include/configs/T102xRDB.h
+++ b/include/configs/T102xRDB.h
@@ -1,7 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:     GPL-2.0+
  */
 
 /*
@@ -13,7 +12,6 @@
 
 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
-#define CONFIG_MP                      /* support multiple processors */
 #define CONFIG_ENABLE_36BIT_PHYS
 
 #ifdef CONFIG_PHYS_64BIT
@@ -34,9 +32,6 @@
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
 #define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE           0x30001000
-#define CONFIG_SPL_TEXT_BASE           0xFFFD8000
 #define CONFIG_SPL_PAD_TO              0x40000
 #define CONFIG_SPL_MAX_SIZE            0x28000
 #define RESET_VECTOR_OFFSET            0x27FFC
@@ -82,7 +77,6 @@
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_RESET_VECTOR_ADDRESS    0x30000FFC
-#define CONFIG_SPL_MMC_MINIMAL
 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x30000000)
 #define CONFIG_SYS_MMC_U_BOOT_START    (0x30000000)
@@ -101,20 +95,10 @@
 
 #endif /* CONFIG_RAMBOOT_PBL */
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE   0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
 #endif
 
-#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
 /* PCIe Boot - Master */
 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 /*
@@ -159,11 +143,6 @@
 #endif
 
 #if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_SPI_BUS             0
-#define CONFIG_ENV_SPI_CS              0
-#define CONFIG_ENV_SPI_MAX_HZ          10000000
-#define CONFIG_ENV_SPI_MODE            0
 #define CONFIG_ENV_SIZE                        0x2000          /* 8KB */
 #define CONFIG_ENV_OFFSET              0x100000        /* 1MB */
 #if defined(CONFIG_TARGET_T1024RDB)
@@ -172,12 +151,10 @@
 #define CONFIG_ENV_SECT_SIZE           0x40000
 #endif
 #elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_SYS_MMC_ENV_DEV         0
 #define CONFIG_ENV_SIZE                        0x2000
 #define CONFIG_ENV_OFFSET              (512 * 0x800)
 #elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_SIZE                        0x2000
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_ENV_OFFSET              (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
@@ -218,7 +195,6 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_MEMTEST_START       0x00200000 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
 
 /*
  *  Config the L3 Cache as L3 SRAM
@@ -232,7 +208,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SPL_RELOC_MALLOC_ADDR   (CONFIG_SPL_GD_ADDR + 12 * 1024)
 #define CONFIG_SPL_RELOC_MALLOC_SIZE   (30 << 10)
 #define CONFIG_SPL_RELOC_STACK         (CONFIG_SPL_GD_ADDR + 64 * 1024)
-#define CONFIG_SPL_RELOC_STACK_SIZE    (22 << 10)
 
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR             0xf0000000
@@ -256,7 +231,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_FSL_DDR_INTERACTIVE
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM 0
@@ -438,9 +412,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -469,7 +440,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_MALLOC_LEN          (10 * 1024 * 1024)
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX      1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
@@ -522,9 +492,6 @@ unsigned long get_board_ddr_clk(void);
 /*
  * eSPI - Enhanced SPI
  */
-#define CONFIG_SPI_FLASH_BAR
-#define CONFIG_SF_DEFAULT_SPEED        10000000
-#define CONFIG_SF_DEFAULT_MODE 0
 
 /*
  * General PCIe
@@ -642,7 +609,6 @@ unsigned long get_board_ddr_clk(void);
  * SDHC
  */
 #ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #endif
 
@@ -683,17 +649,12 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_SYS_DPAA_FMAN
 
-#ifdef CONFIG_TARGET_T1024RDB
-#define CONFIG_QE
-#define CONFIG_U_QE
-#endif
 /* Default address of microcode for the Linux FMan driver */
 #if defined(CONFIG_SPIFLASH)
 /*
  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
  * env, so we got 0x110000.
  */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
 #define CONFIG_SYS_FMAN_FW_ADDR        0x110000
 #define CONFIG_SYS_QE_FW_ADDR  0x130000
 #elif defined(CONFIG_SDCARD)
@@ -702,11 +663,9 @@ unsigned long get_board_ddr_clk(void);
  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
  */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 #define CONFIG_SYS_FMAN_FW_ADDR                (512 * 0x820)
 #define CONFIG_SYS_QE_FW_ADDR          (512 * 0x920)
 #elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #if defined(CONFIG_TARGET_T1024RDB)
 #define CONFIG_SYS_FMAN_FW_ADDR                (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #define CONFIG_SYS_QE_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
@@ -722,10 +681,8 @@ unsigned long get_board_ddr_clk(void);
  * slave SRIO or PCIE outbound window->master inbound window->
  * master LAW->the ucode address in master's memory space.
  */
-#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 #define CONFIG_SYS_FMAN_FW_ADDR                0xFFE00000
 #else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 #define CONFIG_SYS_FMAN_FW_ADDR                0xEFF00000
 #define CONFIG_SYS_QE_FW_ADDR          0xEFE00000
 #endif
@@ -734,10 +691,7 @@ unsigned long get_board_ddr_clk(void);
 #endif /* CONFIG_NOBQFMAN */
 
 #ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB_10G
 #define CONFIG_PHY_REALTEK
-#define CONFIG_PHY_AQUANTIA
 #if defined(CONFIG_TARGET_T1024RDB)
 #define RGMII_PHY1_ADDR                0x2
 #define RGMII_PHY2_ADDR                0x6
@@ -751,18 +705,12 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_FMAN_ENET
-#define CONFIG_MII             /* MII PHY management */
 #define CONFIG_ETHPRIME                "FM1@DTSEC4"
 #endif
 
 /*
  * Dynamic MTD Partition support with mtdparts
  */
-#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_FLASH_CFI_MTD
-#endif
 
 /*
  * Environment
@@ -773,9 +721,6 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 
 /*