#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
#define CONFIG_R360MPI 1
+#define CONFIG_SYS_TEXT_BASE 0x40000000
+
#define CONFIG_LCD
#undef CONFIG_EDT32F10
#define CONFIG_SHARP_LQ057Q3DC02
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
#undef CONFIG_SCC1_ENET
#define CONFIG_SCC2_ENET
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#define CONFIG_MISC_INIT_R /* have misc_init_r() function */
#define CONFIG_CAN_DRIVER /* CAN Driver support enabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */
#undef CONFIG_SORT_I2C /* To I2C with software support */
-#define CFG_I2C_SPEED 4700 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 4700 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* Software (bit-bang) I2C driver configuration
else immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY udelay(50)
-#define CFG_I2C_LCD_ADDR 0x8 /* LCD Control */
-#define CFG_I2C_KEY_ADDR 0x9 /* Keyboard coprocessor */
-#define CFG_I2C_TEM_ADDR 0x49 /* Temperature Sensors */
-
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_BMP | \
- CFG_CMD_BSP | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_NFS | \
- CFG_CMD_PCMCIA | \
- CFG_CMD_SNTP )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_SYS_I2C_LCD_ADDR 0x8 /* LCD Control */
+#define CONFIG_SYS_I2C_KEY_ADDR 0x9 /* Keyboard coprocessor */
+#define CONFIG_SYS_I2C_TEM_ADDR 0x49 /* Temperature Sensors */
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCMCIA
+#define CONFIG_CMD_SNTP
+
/*
* Miscellaneous configurable options
*/
-#define CFG_DEVICE_NULLDEV 1 /* we need the null device */
-#define CFG_CONSOLE_IS_IN_ENV 1 /* must set console from env */
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* we need the null device */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 /* must set console from env */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/* JFFS2 stuff */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-#define CFG_JFFS2_FIRST_SECTOR 24
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition
+ * use all the space starting at offset 3MB*/
+#undef CONFIG_CMD_MTDPARTS
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00300000
+
+/* mtdparts command line support */
+/*
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nor0=r360-0"
+#define MTDPARTS_DEFAULT "mtdparts=r360-0:-@3m(user)"
+*/
/*
* Low Level Configuration Settings
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFF000000
+#define CONFIG_SYS_IMMR 0xFF000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0x40000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0x40000000
#if defined(DEBUG)
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
-#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment */
-#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
-#define CFG_ENV_SIZE 0x4000 /* Used Size of Environment sector */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
+#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment sector */
+#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
-#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR \
+#define CONFIG_SYS_PLPRCR \
( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else /* up to 50 MHz we use a 1:1 clock */
-#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#endif /* CONFIG_80MHz */
/*-----------------------------------------------------------------------
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS | \
+#define CONFIG_SYS_SCCR (SCCR_TBS | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
*-----------------------------------------------------------------------
*
*/
-#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR (0xEC000000)
-#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*/
#if 1
+#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET 0x0100
+#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
#endif
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
*
*/
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
-#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CFG_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
+#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
/*
* FLASH timing:
*/
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_SCY_7_CLK | OR_BI)
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_SCY_7_CLK | OR_BI)
-#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
/*
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-#define CFG_PRELIM_OR2_AM 0xF8000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR2_AM 0xF8000000 /* OR addr mask */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CFG_OR_TIMING_SDRAM (OR_ACS_DIV1 | OR_CSNT_SAM | \
+#define CONFIG_SYS_OR_TIMING_SDRAM (OR_ACS_DIV1 | OR_CSNT_SAM | \
OR_SCY_0_CLK | OR_G5LS)
-#define CFG_OR2_PRELIM (CFG_PRELIM_OR2_AM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR2_AM | CONFIG_SYS_OR_TIMING_SDRAM )
+#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/*
* BR3 and OR3 (CAN Controller)
*/
#ifdef CONFIG_CAN_DRIVER
-#define CFG_CAN_BASE 0xC0000000 /* CAN base address */
-#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA |OR_BI)
-#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
+#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN base address */
+#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
+#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA |OR_BI)
+#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
BR_PS_8 | BR_MS_UPMB | BR_V)
#endif /* CONFIG_CAN_DRIVER */
* 80 Mhz => 80.000.000 / Divider = 156
*/
#if defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA 156
+#define CONFIG_SYS_MAMR_PTA 156
#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA 129
+#define CONFIG_SYS_MAMR_PTA 129
#else /* 50 MHz */
-#define CFG_MAMR_PTA 98
+#define CONFIG_SYS_MAMR_PTA 98
#endif /*CONFIG_??MHz */
/*
* (= 64 ms / 2K = 125 / quad bursts).
* For a simpler initialization, 15.6 us is used instead.
*
- * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
+ * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
+ * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
*/
-#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
-#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
-#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#endif /* __CONFIG_H */