* CONFIG_PPCHAMELEON_CLK_33
*/
#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33))
-#define CONFIG_PPCHAMELEON_CLK_33
+#define CONFIG_PPCHAMELEON_CLK_25
#endif
#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33))
#define CONFIG_MII 1 /* MII PHY management */
#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 0 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 1 /* EMAC1 PHY address */
+#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
+#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
#else
#define CONFIG_PHY_ADDR 2 /* PHY address */
#endif
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
+
+/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */
+#define CONFIG_NEW_NAND_CODE
#define CFG_NAND0_BASE 0xFF400000
#define CFG_NAND1_BASE 0xFF000000
-
-#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
+#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, CFG_NAND1_BASE }
+#define NAND_BIG_DELAY_US 25
+#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
#define SECTORSIZE 512
#define NAND_NO_RB
#define CFG_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
#define CFG_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
+#ifdef CONFIG_NEW_NAND_CODE
+#define MACRO_NAND_DISABLE_CE(nandptr) do \
+{ \
+ switch((unsigned long)nandptr) \
+ { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CE); \
+ break; \
+ } \
+} while(0)
+
+#define MACRO_NAND_ENABLE_CE(nandptr) do \
+{ \
+ switch((unsigned long)nandptr) \
+ { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CE); \
+ break; \
+ } \
+} while(0)
+
+#define MACRO_NAND_CTL_CLRALE(nandptr) do \
+{ \
+ switch((unsigned long)nandptr) \
+ { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_ALE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_ALE); \
+ break; \
+ } \
+} while(0)
+
+#define MACRO_NAND_CTL_SETALE(nandptr) do \
+{ \
+ switch((unsigned long)nandptr) \
+ { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_ALE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_ALE); \
+ break; \
+ } \
+} while(0)
+
+#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
+{ \
+ switch((unsigned long)nandptr) \
+ { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND0_CLE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND1_CLE); \
+ break; \
+ } \
+} while(0)
+
+#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
+ switch((unsigned long)nandptr) { \
+ case CFG_NAND0_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND0_CLE); \
+ break; \
+ case CFG_NAND1_BASE: \
+ out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND1_CLE); \
+ break; \
+ } \
+} while(0)
+#else
#define NAND_DISABLE_CE(nand) do \
{ \
switch((unsigned long)(((struct nand_chip *)nand)->IO_ADDR)) \
break; \
} \
} while(0)
+#endif /* !CONFIG_NEW_NAND_CODE */
#ifdef NAND_NO_RB
/* constant delay (see also tR in the datasheet) */
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
+
+/* Reserve 256 kB for Monitor */
+/*
#define CFG_FLASH_BASE 0xFFFC0000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_LEN (256 * 1024)
+*/
+
+/* Reserve 320 kB for Monitor */
+#define CFG_FLASH_BASE 0xFFFB0000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (320 * 1024)
+
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
/*
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
-#endif
-
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
/* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#endif /* CONFIG_NO_SERIAL_EEPROM */
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */
-#define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */
-#define CONFIG_JFFS2_NAND_SIZE 2*1024*1024 /* size of jffs2 partition */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
+/*
+ * JFFS2 partitions
+ */
+
+/* No command line, one static partition */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nand0"
+#define CONFIG_JFFS2_PART_SIZE 0x00400000
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=PPChameleon-0,nand0=ppchameleonevb-nand"
+*/
+
+/* 256 kB U-boot image */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
+ "1792k(user),256k(u-boot);" \
+ "ppchameleonevb-nand:-(nand)"
+*/
+
+/* 320 kB U-boot image */
+/*
+#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
+ "1728k(user),320k(u-boot);" \
+ "ppchameleonevb-nand:-(nand)"
+*/
+
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff