/*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
#define CONFIG_PM826 1 /* ...on a PM8260 module */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
/* enable I2C and select the hardware/software driver */
* - CONFIG_NET_MULTI must be defined
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#define CONFIG_NET_MULTI
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DOC
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
#ifdef CONFIG_PCI
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DOC | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_PCI)
-#else /* ! PCI */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DOC | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C )
-#endif /* CONFIG_PCI */
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_CMD_PCI
+#endif
+
+
+#define CONFIG_NAND_LEGACY
/*
* Disk-On-Chip configuration
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/*-----------------------------------------------------------------------
* Flash and Boot ROM mapping
*/
-
+#ifdef CONFIG_FLASH_32MB
+#define CFG_FLASH0_BASE 0x40000000
+#define CFG_FLASH0_SIZE 0x02000000
+#else
+#define CFG_FLASH0_BASE 0xFF000000
+#define CFG_FLASH0_SIZE 0x00800000
+#endif
#define CFG_BOOTROM_BASE 0xFF800000
#define CFG_BOOTROM_SIZE 0x00080000
-#define CFG_FLASH0_BASE 0xFF000000
-#define CFG_FLASH0_SIZE 0x02000000
#define CFG_DOC_BASE 0xFF800000
#define CFG_DOC_SIZE 0x00100000
-
/* Flash bank size (for preliminary settings)
*/
#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#ifdef CONFIG_FLASH_32MB
+#define CFG_MAX_FLASH_SECT 135 /* max num of sects on one chip */
+#else
#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-
+#endif
#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
* ---- --- ------- ------ ------
* 0 60x GPCM 64 bit FLASH
* 1 60x SDRAM 64 bit SDRAM
- * 2 Local SDRAM 32 bit SDRAM
*
*/
*/
#define CFG_MIN_AM_MASK 0xC0000000
-#define CFG_MPTPR 0x1F00
+/*
+ * we use the same values for 32 MB and 128 MB SDRAM
+ * refresh rate = 7.73 uS (64 MHz Bus Clock)
+ */
+#define CFG_MPTPR 0x2000
+#define CFG_PSRT 0x0E
#define CFG_MRS_OFFS 0x00000000
/* Bank 2 - SDRAM
*/
-#define CFG_PSRT 0x0F
+
#ifndef CFG_RAMBOOT
#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\