#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
#define CONFIG_PM826 1 /* ...on a PM8260 module */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
"bootm"
/* enable I2C and select the hardware/software driver */
* - CONFIG_NET_MULTI must be defined
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*/
#define CONFIG_NET_MULTI
#undef CONFIG_ETHER_NONE /* define if ether on something else */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DOC
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
#ifdef CONFIG_PCI
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DOC | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_SNTP )
-#else /* ! PCI */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DOC | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
-#endif /* CONFIG_PCI */
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_CMD_PCI
+#endif
+
+
+#define CONFIG_NAND_LEGACY
/*
* Disk-On-Chip configuration
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif