#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#undef CONFIG_NS8382X
-#define ADD_PCI_CMD CFG_CMD_PCI
-
-#else /* MPC5100 */
-
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
-
#endif
/* Partitions */
/* USB */
#if 1
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
#endif
-#if defined(CONFIG_BOOT_ROM)
-#define ADD_DOC_CMD 0
-#else
-#define ADD_DOC_CMD CFG_CMD_DOC
+#if !defined(CONFIG_BOOT_ROM)
+/* DoC requires legacy NAND for now */
+#define CONFIG_NAND_LEGACY
#endif
+
/*
- * Supported commands
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_DOC_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+#if !defined(CONFIG_BOOT_ROM)
+#define CONFIG_CMD_DOC
+#endif
+
+#if defined(CONFIG_MPC5200)
+#define CONFIG_CMD_PCI
+#endif
+
/*
* Autobooting
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/