#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333334 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND "bootm fff00000"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#if 0 /* test-only */
+#define CONFIG_NET_MULTI 1
+
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY1_ADDR 1 /* PHY address */
+#else
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#endif
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_NAND | \
CFG_CMD_DATE | \
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
+#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */
+#define CONFIG_AUTO_UPDATE_SHOW 1 /* use board show routine */
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
+#define CONFIG_AUTOBOOT_STOP_STR " "
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
* NAND-FLASH stuff
*-----------------------------------------------------------------------
*/
+#define CFG_NAND_LEGACY
+
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
+
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
+#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
/* have only 8kB, 16kB is save here */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
projects / oweals / u-boot.git / blobdiff