#define CFG_RESET_ADDR 0x00000000 /* Hard-reset address */
#define CFG_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
-#define CFG_NIOS_SYSID_BASE 0x00920828 /* System id address */
+#define CFG_NIOS_SYSID_BASE 0x021208b8 /* System id address */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
/*------------------------------------------------------------------------
#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */
#define CFG_SDRAM_BASE 0x01000000 /* SDRAM base addr */
#define CFG_SDRAM_SIZE 0x01000000 /* 16 MByte */
-#define CFG_SRAM_BASE 0x00800000 /* SRAM base addr */
-#define CFG_SRAM_SIZE 0x00200000 /* 2 MByte */
+#define CFG_SRAM_BASE 0x02000000 /* SRAM base addr */
+#define CFG_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/
/*------------------------------------------------------------------------
* MEMORY ORGANIZATION
* -Global data is placed below the heap.
* -The stack is placed below global data (&grows down).
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128k */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 128k */
#define CFG_GBL_DATA_SIZE 128 /* Global data size rsvd*/
#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
* CONSOLE
*----------------------------------------------------------------------*/
#if defined(CONFIG_CONSOLE_JTAG)
-#define CFG_NIOS_CONSOLE 0x00920820 /* JTAG UART base addr */
+#define CFG_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
#else
-#define CFG_NIOS_CONSOLE 0x009208a0 /* UART base addr */
+#define CFG_NIOS_CONSOLE 0x02120840 /* UART base addr */
#endif
#define CFG_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
#define CFG_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
+/*------------------------------------------------------------------------
+ * EPCS Device -- wne CFG_NIOS_EPCSBASE is defined code/commands for
+ * epcs device access is enabled. The base address is the epcs
+ * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
+ * The register base is currently at offset 0x600 from the memory base.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_EPCSBASE 0x02100200 /* EPCS register base */
+
/*------------------------------------------------------------------------
* DEBUG
*----------------------------------------------------------------------*/
* registers, we can slow it down to 10 msec using TMRCNT. If the default
* period is acceptable, TMRCNT can be left undefined.
*----------------------------------------------------------------------*/
-#define CFG_NIOS_TMRBASE 0x00920860 /* Tick timer base addr */
+#define CFG_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
#define CFG_NIOS_TMRIRQ 3 /* Timer IRQ num */
#define CFG_NIOS_TMRMS 10 /* 10 msec per tick */
#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
* must implement its own led routines -- leds are, after all,
* board-specific, no?
*----------------------------------------------------------------------*/
-#define CFG_LEDPIO_ADDR 0x00920840 /* LED PIO base addr */
+#define CFG_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
#define CONFIG_STATUS_LED /* Enable status driver */
#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
* way out to avoid changes there -- define the base address to ensure
* cache bypass so there's no need to monkey with inx/outx macros.
*----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE 0x80910300 /* Base addr (bypass) */
+#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
#define CONFIG_DRIVER_SMC91111 /* Using SMC91c111 */
#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
CFG_CMD_SAVES )
#include <cmd_confdefs.h>
+/*------------------------------------------------------------------------
+ * COMPACT FLASH
+ *----------------------------------------------------------------------*/
+#if (CONFIG_COMMANDS & CFG_CMD_IDE)
+#define CONFIG_IDE_PREINIT /* Implement id_preinit */
+#define CFG_IDE_MAXBUS 1 /* 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* 1 drive per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0x00900800 /* ATA base addr */
+#define CFG_ATA_IDE0_OFFSET 0x0000 /* IDE0 offset */
+#define CFG_ATA_DATA_OFFSET 0x0040 /* Data IO offset */
+#define CFG_ATA_REG_OFFSET 0x0040 /* Register offset */
+#define CFG_ATA_ALT_OFFSET 0x0100 /* Alternate reg offset */
+#define CFG_ATA_STRIDE 4 /* Width betwix addrs */
+#define CONFIG_DOS_PARTITION
+
+/* Board-specific cf regs */
+#define CFG_CF_PRESENT 0x00900880 /* CF Present PIO base */
+#define CFG_CF_POWER 0x00900890 /* CF Power FET PIO base*/
+#define CFG_CF_ATASEL 0x009008a0 /* CF ATASEL PIO base */
+
+#endif /* CONFIG_COMMANDS & CFG_CMD_IDE */
+
+/*------------------------------------------------------------------------
+ * JFFS2
+ *----------------------------------------------------------------------*/
+#if (CONFIG_COMMANDS & CFG_CMD_JFFS2)
+#define CFG_JFFS_CUSTOM_PART /* board defined part */
+#endif
+
/*------------------------------------------------------------------------
* MISC
*----------------------------------------------------------------------*/
#define CFG_MEMTEST_START CFG_SDRAM_BASE /* Start addr for test */
#define CFG_MEMTEST_END CFG_INIT_SP - 0x00020000
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
#endif /* __CONFIG_H */