/*
- * Copyright 2007-2010 Freescale Semiconductor, Inc.
+ * Copyright 2007-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#include "../board/freescale/common/ics307_clk.h"
-#ifdef CONFIG_MK_36BIT
+#ifdef CONFIG_36BIT
#define CONFIG_PHYS_64BIT
#endif
+#ifdef CONFIG_SDCARD
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_P2020DS 1
#define CONFIG_MP 1 /* support multiple processors */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1 /* SRIO port 1 */
+#define CONFIG_SRIO2 /* SRIO port 2 */
+
#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
+
#define CONFIG_ENABLE_36BIT_PHYS 1
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
#endif
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x7fffffff
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
+ * Config the L2 Cache
*/
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
#else
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#endif
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_L2_SIZE (512 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
+#ifdef CONFIG_DDR2
+#define CONFIG_FSL_DDR2
+#else
#define CONFIG_FSL_DDR3 1
-#undef CONFIG_FSL_DDR_INTERACTIVE
+#endif
/* ECC will be enabled based on perf_mode environment variable */
/* #define CONFIG_DDR_ECC */
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
/* I2C addresses of SPD EEPROMs */
+#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD EEPROM located on I2C bus 0 */
-#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
/* These are used when DDR doesn't use SPD. */
#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1GB */
*
*/
-#undef CONFIG_CLOCKS_IN_MHZ
-
/*
* Memory map
*
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
-#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
+#define CONFIG_FLASH_BR_PRELIM \
+ (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM 0xf8000ff7
#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_HWCONFIG /* enable hwconfig */
#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */
#ifdef CONFIG_FSL_NGPIXIS
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
#endif
-#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
/* NAND flash config */
-#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
-#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
+#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
| OR_FCM_PGS /* Large Page*/ \
| OR_FCM_CSCT \
| OR_FCM_CST \
#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
-#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
-#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
/*
* Pass open firmware flat tree
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_BUS_NUM 0
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 3, Slot 1, tgtid 3, Base address b000 */
+#define CONFIG_SYS_PCIE3_NAME "Slot 1"
#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME "ULI"
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 2, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "Slot 2"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
#endif
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-#define CONFIG_RTL8139
+/* SRIO1 uses the same window as PCIE2 mem window */
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
- #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
+/* SRIO2 uses the same window as PCIE1 mem window */
+#define CONFIG_SYS_SRIO2_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc0000000
#endif
+#define CONFIG_SYS_SRIO2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI
#if defined(CONFIG_TSEC_ENET)
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
-#define CONFIG_PIXIS_SGMII_CMD
#define CONFIG_FSL_SGMII_RISER 1
#define SGMII_RISER_PHY_OFFSET 0x1b
/*
* Environment
*/
+#if defined(CONFIG_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#elif defined(CONFIG_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#else
#define CONFIG_ENV_IS_IN_FLASH 1
#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
#define CONFIG_ENV_ADDR 0xfff80000
#endif
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* USB
*/
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#endif
+#endif
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+/*
+ * SDHC/MMC
+ */
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
/*
* For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD
-#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.254
#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH /opt/nfsroot
-#define CONFIG_BOOTFILE uImage
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
- "perf_mode=stable\0" \
- "memctl_intlv_ctl=2\0" \
- "netdev=eth0\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=p2020ds/ramdisk.uboot\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=p2020ds/p2020ds.dtb\0" \
- "bdev=sda3\0"
+"perf_mode=performance\0" \
+ "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \
+ "usb1:dr_mode=host,phy_type=ulpi\0" \
+"netdev=eth0\0" \
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+"tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
+ "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
+"satabootcmd=setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr" \
+"consoledev=ttyS0\0" \
+"ramdiskaddr=2000000\0" \
+"ramdiskfile=p2020ds/ramdisk.uboot\0" \
+"fdtaddr=c00000\0" \
+"othbootargs=cache-sram-size=0x10000\0" \
+"fdtfile=p2020ds/p2020ds.dtb\0" \
+"bdev=sda3\0" \
+"partition=scsi 0:0\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
+ "ext2load $partition $loadaddr $bootfile;" \
+ "ext2load $partition $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_NFSBOOTCOMMAND \