/*
- * Copyright 2010 Freescale Semiconductor, Inc.
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
* Timur Tabi <timur@freescale.com>
*
#include "../board/freescale/common/ics307_clk.h"
+#ifdef CONFIG_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE /* BOOKE */
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_P1022DS
#define CONFIG_MP /* support multiple processors */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_SYS_HAS_SERDES /* has SERDES */
-#define CONFIG_PHYS_64BIT
#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
+#endif
#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_SYS_MEMTEST_START 0x00000000
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR 0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_DDR_SPD
/* I2C addresses of SPD EEPROMs */
#define CONFIG_SYS_SPD_BUS_NUM 1
-#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
/*
* Memory map
* Local Bus Definitions
*/
#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
#define CONFIG_FLASH_BR_PRELIM \
(BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
#define CONFIG_SYS_MAX_FLASH_BANKS 2
#define CONFIG_SYS_MAX_FLASH_SECT 1024
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
#define CONFIG_FSL_NGPIXIS
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
#define PIXIS_BASE_PHYS 0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS PIXIS_BASE
+#endif
#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7)
#define PIXIS_LBMAP_SWITCH 7
-#define PIXIS_LBMAP_MASK 0xE0
+#define PIXIS_LBMAP_MASK 0xF0
#define PIXIS_LBMAP_ALTBANK 0x20
+#define PIXIS_ELBC_SPI_MASK 0xc0
+#define PIXIS_SPI 0x80
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/* Video */
-#undef CONFIG_FSL_DIU_FB
+#define CONFIG_FSL_DIU_FB
#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000)
#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+
+#ifndef CONFIG_FSL_DIU_FB
+#define CONFIG_ATI
+#endif
+
+#ifdef CONFIG_ATI
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
+#define CONFIG_VIDEO
+#define CONFIG_BIOSEMU
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
#endif
/*
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_BUS_NUM 1
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
+#endif
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#endif
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 3, Base address b000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
+#endif
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
+#endif
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PCI
-#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_E1000 /* Define e1000 pci Ethernet card */
#endif
/* SATA */
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
+#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#ifdef CONFIG_TSEC_ENET
#define CONFIG_TSECV2
-#define CONFIG_NET_MULTI
#define CONFIG_MII /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
/*
* For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
*/
#define CONFIG_HOSTNAME p1022ds
-#define CONFIG_ROOTPATH /opt/nfsroot
-#define CONFIG_BOOTFILE uImage
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_LOADADDR 1000000
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=uramdisk\0" \
"diuregs=md e002c000 1d\0" \
"dium=mw e002c01c\0" \
"diuerr=md e002c014 1\0" \
- "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \
- "monitor=0-DVI\0"
+ "hwconfig=esdhc;audclk:12\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \