arc: add Arcangel4 board support

[oweals/u-boot.git] / include / configs / P1010RDB.h

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index c6b9acac3bad17373533e7fdd1ff7d85df5b221c..f82fbca77cfd2425b1e754a7274daca611de2a77 100644 (file)
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -23,13 +23,13 @@
 #ifdef CONFIG_SDCARD
 #define CONFIG_RAMBOOT_SDCARD
 #define CONFIG_SYS_TEXT_BASE           0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS    0x1107fffc
+#define CONFIG_RESET_VECTOR_ADDRESS    0x110bfffc
 #endif
 
 #ifdef CONFIG_SPIFLASH
 #define CONFIG_RAMBOOT_SPIFLASH
 #define CONFIG_SYS_TEXT_BASE           0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS    0x1107fffc
+#define CONFIG_RESET_VECTOR_ADDRESS    0x110bfffc
 #endif
 
 #ifdef CONFIG_NAND
@@ -37,7 +37,7 @@
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"
 
@@ -46,7 +46,7 @@
 #define CONFIG_SPL_MAX_SIZE            8192
 #define CONFIG_SPL_RELOC_TEXT_BASE     0x00100000
 #define CONFIG_SPL_RELOC_STACK         0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE    ((512 << 10) - 0x2000)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE    ((768 << 10) - 0x2000)
 #define CONFIG_SYS_NAND_U_BOOT_DST     (0x00200000 - CONFIG_SPL_MAX_SIZE)
 #define CONFIG_SYS_NAND_U_BOOT_START   0x00200000
 #define CONFIG_SYS_NAND_U_BOOT_OFFS    0
@@ -57,11 +57,11 @@
 #ifdef CONFIG_NAND_SECBOOT     /* NAND Boot */
 #define CONFIG_RAMBOOT_NAND
 #define CONFIG_SYS_TEXT_BASE           0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS    0x1107fffc
+#define CONFIG_RESET_VECTOR_ADDRESS    0x110bfffc
 #endif
 
 #ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE           0xeff80000
+#define CONFIG_SYS_TEXT_BASE           0xeff40000
 #endif
 
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
@@ -77,7 +77,6 @@
 /* High Level Configuration Options */
 #define CONFIG_BOOKE                   /* BOOKE */
 #define CONFIG_E500                    /* BOOKE e500 family */
-#define CONFIG_MPC85xx
 #define CONFIG_FSL_IFC                 /* Enable IFC Support */
 #define CONFIG_SYS_HAS_SERDES          /* common SERDES init code */
 
@@ -173,12 +172,12 @@
 #define CONFIG_SYS_NUM_ADDR_MAP                16      /* number of TLB1 entries */
 #endif
 
-#define CONFIG_SYS_MEMTEST_START       0x00000000      /* memtest works on */
+#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x1fffffff
 #define CONFIG_PANIC_HANG              /* do not reset board on panic */
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM         1
@@ -313,6 +312,13 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
 #endif
 
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITION
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT                 "nand0=ff800000.flash"
+#define MTDPARTS_DEFAULT               \
+       "mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
+
 #define CONFIG_SYS_NAND_CSPR   (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8      \
                                | CSPR_MSEL_NAND        \
@@ -654,18 +660,14 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_ENV_SIZE                (16 * 1024)
 #define CONFIG_ENV_RANGE       (32 * CONFIG_ENV_SIZE) /* new block size 512K */
 #endif
-#define CONFIG_ENV_OFFSET      ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET      ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_ENV_IS_NOWHERE          /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                        (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                        0x2000
 #else
 #define CONFIG_ENV_IS_IN_FLASH
-#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
-#define CONFIG_ENV_ADDR        0xfff80000
-#else
 #define CONFIG_ENV_ADDR        (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#endif
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
 #endif
@@ -703,7 +705,6 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
@@ -714,7 +715,6 @@ extern unsigned long get_sdram_size(void);
                                                /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ          1000            /* dec freq: 1ms ticks */
 
 /*
  * Internal Definitions
@@ -734,7 +734,6 @@ extern unsigned long get_sdram_size(void);
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /*