#define CONFIG_MPC86xx 1 /* MPC86xx */
#define CONFIG_MPC8641 1 /* MPC8641 specific */
#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
-#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
-#undef DEBUG
+#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
#ifdef RUN_DIAG
-#define CFG_DIAG_ADDR 0xff800000
+#define CFG_DIAG_ADDR 0xff800000
#endif
#define CFG_RESET_ADDRESS 0xfff00100
#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */
#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_FSL_LAW 1 /* Use common FSL law init code */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_NUM_DDR_CONTROLLERS 2
-/* #define CONFIG_DDR_INTERLEAVE 1 */
+/* #define CONFIG_DDR_INTERLEAVE 1 */
#define CACHE_LINE_INTERLEAVING 0x20000000
#define PAGE_INTERLEAVING 0x21000000
#define BANK_INTERLEAVING 0x22000000
#define SUPER_BANK_INTERLEAVING 0x23000000
+#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
-#define CONFIG_ALTIVEC 1
+#define CONFIG_ALTIVEC 1
/*
* L2CR setup -- make sure this is right for your board!
#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy);
#endif
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
#define CFG_DDR_CS0_BNDS 0x0000000F
- #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
+ #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
#define CFG_DDR_EXT_REFRESH 0x00000000
- #define CFG_DDR_TIMING_0 0x00260802
+ #define CFG_DDR_TIMING_0 0x00260802
#define CFG_DDR_TIMING_1 0x39357322
#define CFG_DDR_TIMING_2 0x14904cc8
#define CFG_DDR_MODE_1 0x00480432
#define CFG_DDR_MODE_2 0x00000000
#define CFG_DDR_INTERVAL 0x06090100
- #define CFG_DDR_DATA_INIT 0xdeadbeef
- #define CFG_DDR_CLK_CTRL 0x03800000
- #define CFG_DDR_OCD_CTRL 0x00000000
- #define CFG_DDR_OCD_STATUS 0x00000000
+ #define CFG_DDR_DATA_INIT 0xdeadbeef
+ #define CFG_DDR_CLK_CTRL 0x03800000
+ #define CFG_DDR_OCD_CTRL 0x00000000
+ #define CFG_DDR_OCD_STATUS 0x00000000
#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
#define CFG_DDR_CONTROL2 0x04400000
#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
#endif
-#define CFG_ID_EEPROM 1
-#define ID_EEPROM_ADDR 0x57
+#define CONFIG_ID_EEPROM
+#define CFG_I2C_EEPROM_NXID
+#define CFG_ID_EEPROM
+#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_I2C_EEPROM_ADDR_LEN 1
/*
* In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
*
* Note that, on switching the boot location, fef00000 becomes fff00000.
*/
-#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
+#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
#define CFG_FLASH_BASE2 0xff800000
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
-#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
+#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#if defined(CFG_RAMBOOT)
#else
#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
#endif
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/*
* Pass open firmware flat tree to kernel
*/
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define OF_CPU "PowerPC,8641@0"
-#define OF_SOC "soc8641@f8000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
#define CFG_64BIT_VSPRINTF 1
#define CFG_64BIT_STRTOUL 1
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3100
/*
#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
/* For RTL8139 */
#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
-#define _IO_BASE 0x00000000
+#define _IO_BASE 0x00000000
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#if defined(CONFIG_PCI)
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#undef CFG_SCSI_SCAN_BUS_REVERSE
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_RTL8139
/************************************************************
* USB support
************************************************************/
-#define CONFIG_PCI_OHCI 1
+#define CONFIG_PCI_OHCI 1
#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_USB_KEYBOARD 1
+#define CONFIG_USB_KEYBOARD 1
#define CFG_DEVICE_DEREGISTER
-#define CFG_USB_EVENT_POLL 1
-#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CFG_USB_EVENT_POLL 1
+#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#define CFG_OHCI_SWAP_REG_ACCESS 1
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
/*PCIE video card used*/
#define CONFIG_SATA_ULI5288
#define CFG_SCSI_MAX_SCSI_ID 4
#define CFG_SCSI_MAX_LUN 1
-#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
#endif
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-#define CONFIG_TSEC4 1
-#define CONFIG_TSEC4_NAME "eTSEC4"
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#endif /* CONFIG_TSEC_ENET */
/*
- * BAT0 2G Cacheable, non-guarded
- * 0x0000_0000 2G DDR
+ * BAT0 2G Cacheable, non-guarded
+ * 0x0000_0000 2G DDR
*/
-#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
-#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
-#define CFG_IBAT0U CFG_DBAT0U
+#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U CFG_DBAT0U
/*
- * BAT1 1G Cache-inhibited, guarded
- * 0x8000_0000 512M PCI-Express 1 Memory
- * 0xa000_0000 512M PCI-Express 2 Memory
+ * BAT1 1G Cache-inhibited, guarded
+ * 0x8000_0000 512M PCI-Express 1 Memory
+ * 0xa000_0000 512M PCI-Express 2 Memory
* Changed it for operating from 0xd0000000
*/
-#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
+#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT1U CFG_DBAT1U
+#define CFG_IBAT1U CFG_DBAT1U
/*
- * BAT2 512M Cache-inhibited, guarded
- * 0xc000_0000 512M RapidIO Memory
+ * BAT2 512M Cache-inhibited, guarded
+ * 0xc000_0000 512M RapidIO Memory
*/
-#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \
+#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT2U (CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
#define CFG_IBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U CFG_DBAT2U
+#define CFG_IBAT2U CFG_DBAT2U
/*
- * BAT3 4M Cache-inhibited, guarded
- * 0xf800_0000 4M CCSR
+ * BAT3 4M Cache-inhibited, guarded
+ * 0xf800_0000 4M CCSR
*/
-#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U CFG_DBAT3U
+#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U CFG_DBAT3U
/*
- * BAT4 32M Cache-inhibited, guarded
- * 0xe200_0000 16M PCI-Express 1 I/O
- * 0xe300_0000 16M PCI-Express 2 I/0
+ * BAT4 32M Cache-inhibited, guarded
+ * 0xe200_0000 16M PCI-Express 1 I/O
+ * 0xe300_0000 16M PCI-Express 2 I/0
* Note that this is at 0xe0000000
*/
-#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
+#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT4U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT4L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT4U CFG_DBAT4U
+#define CFG_IBAT4U CFG_DBAT4U
/*
- * BAT5 128K Cacheable, non-guarded
- * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ * BAT5 128K Cacheable, non-guarded
+ * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
-#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT5L CFG_DBAT5L
-#define CFG_IBAT5U CFG_DBAT5U
+#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L CFG_DBAT5L
+#define CFG_IBAT5U CFG_DBAT5U
/*
- * BAT6 32M Cache-inhibited, guarded
- * 0xfe00_0000 32M FLASH
+ * BAT6 32M Cache-inhibited, guarded
+ * 0xfe00_0000 32M FLASH
*/
-#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U CFG_DBAT6U
+#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U CFG_DBAT6U
#define CFG_DBAT7L 0x00000000
#define CFG_DBAT7U 0x00000000
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:E0:0C:00:00:01
+#define CONFIG_ETHADDR 00:E0:0C:00:00:01
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "dtbaddr=c00000\0" \
- "dtbfile=mpc8641_hpcn.dtb\0" \
- "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
- "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
- "maxcpus=2"
-
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr - $dtbaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr $ramdiskaddr $dtbaddr"
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=mpc8641_hpcn.dtb\0" \
+ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "maxcpus=2"
+
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND