m68k: Drop CONFIG_MCFPIT support

[oweals/u-boot.git] / include / configs / MPC8610HPCD.h

diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index ddfb241010ae33d0faae087143a38baa9dfb792f..8b10a6cfef94362a1fc0cfc3f078639098dd35f1 100644 (file)
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -43,7 +43,6 @@
 #define CONFIG_INTERRUPTS              /* enable pci, srio, ddr interrupts */
 
 #define CONFIG_BAT_RW          1       /* Use common BAT rw code */
-#define CONFIG_HIGH_BATS       1       /* High BATs supported & enabled */
 #define CONFIG_ALTIVEC         1
 
 /*
@@ -57,8 +56,6 @@
 #define CONFIG_SYS_CLK_FREQ    get_board_sys_clk(0)
 #endif
 
-#define CONFIG_MISC_INIT_R             1
-
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 
@@ -74,7 +71,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS                CONFIG_SYS_CCSRBAR_PHYS_LOW
 
 /* DDR Setup */
-#undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD for DDR */
 #define CONFIG_DDR_SPD
 
@@ -168,8 +164,6 @@
 #define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000     /* early monitor loc */
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
@@ -280,7 +274,6 @@
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID    4
 #define CONFIG_SYS_SCSI_MAX_LUN        1
 #define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE      CONFIG_SYS_SCSI_MAX_DEVICE
 #endif
 
 #endif /* CONFIG_PCI */
@@ -390,14 +383,6 @@
 /*
  * Environment
  */
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE   0x20000 /* 126k (one sector) for env */
-#define CONFIG_ENV_SIZE                0x2000
-#else
-#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE                0x2000
-#endif
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */