#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ 33333333 /* ICS307 clock chip ref freq */
+#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq
from ICS307 instead of switches */
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_ENABLE_36BIT_PHYS 1
-#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x7fffffff
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x7fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
-#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#endif
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
-#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */
+#define CONFIG_SYS_DDR_TLB_START 9
+#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#undef CONFIG_DDR_DLL
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
/* I2C addresses of SPD EEPROMs */
+#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD EEPROMS locate on I2C bus 1 */
#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */
#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */
/* These are used when DDR doesn't use SPD. */
-#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
-#define CFG_DDR_CS0_BNDS 0x0000001F
-#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_TIMING_0 0x00260802
-#define CFG_DDR_TIMING_1 0x3935d322
-#define CFG_DDR_TIMING_2 0x14904cc8
-#define CFG_DDR_MODE_1 0x00480432
-#define CFG_DDR_MODE_2 0x00000000
-#define CFG_DDR_INTERVAL 0x06180100
-#define CFG_DDR_DATA_INIT 0xdeadbeef
-#define CFG_DDR_CLK_CTRL 0x03800000
-#define CFG_DDR_OCD_CTRL 0x00000000
-#define CFG_DDR_OCD_STATUS 0x00000000
-#define CFG_DDR_CONTROL 0xC3008000 /* Type = DDR2 */
-#define CFG_DDR_CONTROL2 0x04400010
-
-#define CFG_DDR_ERR_INT_EN 0x0000000d
-#define CFG_DDR_ERR_DIS 0x00000000
-#define CFG_DDR_SBE 0x00010000
-
-/*
- * FIXME: Not used in fixed_sdram function
- */
-#define CFG_DDR_MODE 0x00000022
-#define CFG_DDR_CS1_BNDS 0x00000000
-#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
+#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3 0x00020000
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x626b2634
+#define CONFIG_SYS_DDR_TIMING_2 0x062874cf
+#define CONFIG_SYS_DDR_MODE_1 0x00440462
+#define CONFIG_SYS_DDR_MODE_2 0x00000000
+#define CONFIG_SYS_DDR_INTERVAL 0x0c300100
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL 0x00800000
+#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
+#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
+#define CONFIG_SYS_DDR_CONTROL 0xc3000008 /* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2 0x24400000
+
+#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
+#define CONFIG_SYS_DDR_SBE 0x00010000
/*
* Make sure required options are set
* Localbus non-cacheable
* 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
* 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
+ * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
* 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
/*
* Local Bus Definitions
*/
-#define CFG_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
+#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
-#define CFG_BR0_PRELIM 0xe8001001
-#define CFG_OR0_PRELIM 0xf8000ff7
+#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM 0xf8000ff7
-#define CFG_BR1_PRELIM 0xe0001001
-#define CFG_OR1_PRELIM 0xf8000ff7
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE + 0x8000000, CFG_FLASH_BASE}
-#define CFG_FLASH_QUIET_TEST
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
-#define CFG_FLASH_AMD_CHECK_DQ7
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS 0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS PIXIS_BASE
+#endif
-#define CFG_BR3_PRELIM (PIXIS_BASE | 0x0801) /* port size 8bit */
-#define CFG_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
/* old pixis referenced names */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CFG_PIXIS_VBOOT_MASK 0xc0
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#define CFG_INIT_RAM_END 0x00004000 /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0
+#define PIXIS_VSPEED2_TSEC1SER 0x8
+#define PIXIS_VSPEED2_TSEC2SER 0x4
+#define PIXIS_VSPEED2_TSEC3SER 0x2
+#define PIXIS_VSPEED2_TSEC4SER 0x1
+#define PIXIS_VCFGEN1_TSEC1SER 0x20
+#define PIXIS_VCFGEN1_TSEC2SER 0x20
+#define PIXIS_VCFGEN1_TSEC3SER 0x20
+#define PIXIS_VCFGEN1_TSEC4SER 0x20
+#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \
+ | PIXIS_VSPEED2_TSEC2SER \
+ | PIXIS_VSPEED2_TSEC3SER \
+ | PIXIS_VSPEED2_TSEC4SER)
+#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \
+ | PIXIS_VCFGEN1_TSEC2SER \
+ | PIXIS_VCFGEN1_TSEC3SER \
+ | PIXIS_VCFGEN1_TSEC4SER)
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\
+ CONFIG_SYS_NAND_BASE + 0x40000, \
+ CONFIG_SYS_NAND_BASE + 0x80000,\
+ CONFIG_SYS_NAND_BASE + 0xC0000}
+#define CONFIG_SYS_MAX_NAND_DEVICE 4
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
+ | OR_FCM_PGS /* Large Page*/ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR)
+
+#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+
+#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+
+#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port - controlled on board with jumper J8
* open - index 2
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CFG_64BIT_VSPRINTF 1
-#define CFG_64BIT_STRTOUL 1
+#define CONFIG_SYS_64BIT_VSPRINTF 1
+#define CONFIG_SYS_64BIT_STRTOUL 1
/* new uImage format support */
#define CONFIG_FIT 1
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR 0x57
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3100
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM 1
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
-/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
-
/* controller 3, direct to uli, tgtid 3, Base address 8000 */
-#define CFG_PCIE3_MEM_BASE 0x80000000
-#define CFG_PCIE3_MEM_PHYS CFG_PCIE3_MEM_BASE
-#define CFG_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCIE3_IO_BASE 0x00000000
-#define CFG_PCIE3_IO_PHYS 0xffc00000
-#define CFG_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CFG_PCIE2_MEM_BASE 0xa0000000
-#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
-#define CFG_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCIE2_IO_BASE 0x00000000
-#define CFG_PCIE2_IO_PHYS 0xffc10000
-#define CFG_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CFG_PCIE1_MEM_BASE 0xc0000000
-#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCIE1_IO_BASE 0x00000000
-#define CFG_PCIE1_IO_PHYS 0xffc20000
-#define CFG_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#if defined(CONFIG_PCI)
/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CFG_PCIE1_IO_PHYS
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
/* video */
#define CONFIG_VIDEO
#define CONFIG_ATI_RADEON_FB
#define CONFIG_VIDEO_LOGO
/*#define CONFIG_CONSOLE_CURSOR*/
-#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
#endif
#define CONFIG_NET_MULTI
#endif
#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CFG_PCIE3_IO_BASE
- #define PCI_ENET0_MEMADDR CFG_PCIE3_IO_BASE
+ #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
+ #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
#endif
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID 4
-#define CFG_SCSI_MAX_LUN 1
-#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif /* SCSI */
#endif /* CONFIG_PCI */
#define CONFIG_TSEC4 1
#define CONFIG_TSEC4_NAME "eTSEC4"
+#define CONFIG_PIXIS_SGMII_CMD
+#define CONFIG_FSL_SGMII_RISER 1
+#define SGMII_RISER_PHY_OFFSET 0x1c
+
+#ifdef CONFIG_FSL_SGMII_RISER
+#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */
+#endif
+
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#if CFG_MONITOR_BASE > 0xfff80000
-#define CFG_ENV_ADDR 0xfff80000
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
#else
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#endif
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Command line configuration.
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_ELF
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_SETEXPR
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "memctl_intlv_ctl=2\0" \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \