/*
- * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ * Copyright 2007-2008,2010 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#ifndef __CONFIG_H
#define __CONFIG_H
+#include "../board/freescale/common/ics307_clk.h"
+
+#ifdef CONFIG_MK_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC8572 1
#define CONFIG_MPC8572DS 1
#define CONFIG_MP 1 /* support multiple processors */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the CDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-extern unsigned long get_board_ddr_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */
#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */
-#define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq
- from ICS307 instead of switches */
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_ENABLE_36BIT_PHYS 1
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
+#endif
+
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
*/
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull /* physical addr of CCSRBAR */
+#else
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#endif
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
-#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
-
/* DDR Setup */
+#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#undef CONFIG_DDR_DLL
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */
/* These are used when DDR doesn't use SPD. */
-#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 0x00260802
-#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
-#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
-#define CONFIG_SYS_DDR_MODE_1 0x00480432
+#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3 0x00020000
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x626b2634
+#define CONFIG_SYS_DDR_TIMING_2 0x062874cf
+#define CONFIG_SYS_DDR_MODE_1 0x00440462
#define CONFIG_SYS_DDR_MODE_2 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL 0x06180100
+#define CONFIG_SYS_DDR_INTERVAL 0x0c300100
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
-#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
+#define CONFIG_SYS_DDR_CLK_CTRL 0x00800000
+#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xC3008000 /* Type = DDR2 */
-#define CONFIG_SYS_DDR_CONTROL2 0x04400010
+#define CONFIG_SYS_DDR_CONTROL 0xc3000008 /* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2 0x24400000
#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
* Localbus non-cacheable
* 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable
* 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable
+ * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
* 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
* Local Bus Definitions
*/
#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
-#define CONFIG_SYS_BR0_PRELIM 0xe8001001
-#define CONFIG_SYS_OR0_PRELIM 0xf8000ff7
+#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM 0xf8000ff7
-#define CONFIG_SYS_BR1_PRELIM 0xe0001001
-#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE + 0x8000000, CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS 0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS PIXIS_BASE
+#endif
-#define CONFIG_SYS_BR3_PRELIM (PIXIS_BASE | 0x0801) /* port size 8bit */
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VBOOT_LBMAP 0xc0 /* VBOOT - CFG_LBMAP */
+#define PIXIS_VBOOT_LBMAP_NOR0 0x00 /* cfg_lbmap - boot from NOR 0 */
+#define PIXIS_VBOOT_LBMAP_PJET 0x01 /* cfg_lbmap - boot from projet */
+#define PIXIS_VBOOT_LBMAP_NAND 0x02 /* cfg_lbmap - boot from NAND */
+#define PIXIS_VBOOT_LBMAP_NOR1 0x03 /* cfg_lbmap - boot from NOR 1 */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */
| PIXIS_VCFGEN1_TSEC3SER \
| PIXIS_VCFGEN1_TSEC4SER)
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\
+ CONFIG_SYS_NAND_BASE + 0x40000, \
+ CONFIG_SYS_NAND_BASE + 0x80000,\
+ CONFIG_SYS_NAND_BASE + 0xC0000}
+#define CONFIG_SYS_MAX_NAND_DEVICE 4
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
+ | OR_FCM_PGS /* Large Page*/ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR)
+
+#define CONFIG_SYS_BR2_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+
+#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR4_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR5_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+
+#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8 bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_OR6_PRELIM CONFIG_NAND_OR_PRELIM /* NAND Options */
+
+
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CONFIG_SYS_64BIT_VSPRINTF 1
-#define CONFIG_SYS_64BIT_STRTOUL 1
-
/* new uImage format support */
#define CONFIG_FIT 1
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_SLAVE 0x7F
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
-/* PCI view of System Memory */
-#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
-
/* controller 3, direct to uli, tgtid 3, Base address 8000 */
-#define CONFIG_SYS_PCIE3_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_BASE
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
+#endif
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull
+#else
#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
+#endif
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_MEM_BASE 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
+#else
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#endif
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull
+#else
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
+#endif
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#if defined(CONFIG_PCI)
/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_PHYS
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT
/* video */
#define CONFIG_VIDEO
#undef CONFIG_TULIP
#undef CONFIG_RTL8139
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#define _IO_BASE 0x00000000
-#endif
-
#ifndef CONFIG_PCI_PNP
- #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BASE
- #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BASE
+ #define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
+ #define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
#define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */
#endif
#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
#define CONFIG_ENV_ADDR 0xfff80000
#else
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x70000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#endif
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_NET
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions